Question about Audio & Video Receivers

1 Answer

The music was to loud and the amp went off.wont play any source

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 86 Answers

Check your fuses, sounds like somthing may of blown, it mite of been too loud were you couldnt hear the amp making a click sound, when that happens a fuse can go at anytime

Posted on Oct 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Amp wont play


Quick test...with your Lanzar volume all the way down, connect MP3 player or other type audio source directly to the subwoofer input connection. Play audio and slowly increase volume control. If subwoofer is working using this method, reconnect and check for audio output to Lanzer connection problem, or subwoofer "settings" issues with the receiver.

Nov 11, 2013 | Lanzar VCTBS8 Vector 8-Inch Super-Slim...

1 Answer

Speakers and headphones do not work


Sadly this could indicate that the main power amp has failed. You should try turning it up really loud with some music playing. If you can hear it very faint, then the main amp has failed. If you can hear hum, then the pre-amp might be the cause. The only other cause is that the headphone socket has broken, cutting off both speakers and headphones.

Aug 06, 2013 | Onkyo Audio & Video Receivers

1 Answer

I have a MARANTZ SR7000 Receiver . I would like to play music CDs in direct source mode and also be able to use the subwoofer. How does one do that.


Not sure that this will be possible, direct source will cut out any changes made by the amp, and as a cd is 2 channel stereo, it wont include the subwoofer. Try some of the other settings with direct source mode.

May 03, 2011 | Marantz SR-7000 Receiver

1 Answer

The speakers on the left side of my technics stereo have stopped working and are making a loud humming sound while the speakers on the right side still play music normally model number is sa-120 and the...


Check the input cables from the source you are playing at both ends. Sounds like an input problem, not a speaker problem. Twist the RCA connectors as you push them in to make sure the connection is good.

Aug 29, 2010 | Audio & Video Receivers

1 Answer

Technics su z2 amp shuts off sound


hello. we cant help if we dont know what music source you are using.

Apr 13, 2009 | Technics SA-AX530 Receiver

1 Answer

Onkyo SR606 - Loud Poping


It could be a number of things,
1. an electrical short in the house. Try plugging it into another circuit with an extension cord.
2. A bad RCA cable that is input from one of your sources.
3. its probably a bad unit if you have Zone one and two playing at the same time the same source, but it only happens on zone 1.
4. a bad speaker can make a poping like sound, does it happen on all speakers? unplug all but one and one at a time try to determine if the problem sticks, if not, then one of the speakers is out of phase or blown.
5. Playing music froma computer source will sometimes make a pop if your computer is slow or bogged down with checking emails..etc. mine sometimes studders PPPPPPPrioRRRRRity CCCCCLLLLLLLLEEEEERRRRANCCCEE AAAAAAALLLLPPPPPHAAAA OOOOOOONE.
it also pops real loud when booting or shutting down.
Personal note ........windows is such a hassle for Media systems.


I hope something here helps!


Charles




Dec 31, 2008 | Onkyo TX-SR606 Receiver

1 Answer

When i play music loud the sound cuts out


i would try getting a new amp, the speakers may be blown.

Dec 30, 2008 | Audio & Video Receivers

1 Answer

My Kenwood amplifier is having problems, whenever i turn it on. all seems well until i play some music through it, after 30seconds to a minute the music will cut off and a distinct click is sometimes...


Your amp is going into protection. The click you hear is a relay meant to protect your speakers and stereo. Check your speakers with an ohm meter for the the proper ohms ( listed on the speaker ) and physically try to push each woofer and midrange cone in gently to make sure it moves and is not stuck or frozen in place. A speaker may read correctly on an ohm meter if the woofer is ok but if the tweeter or midrange is not working it will cause the amp to go into protection mode. When you play music stick your ear up to each tweeter\midrange\woofer to ensure they are working.
Your stereo could also be the culprit although usually if it plays music it is ok as long as you are not hearing loud pops. Loud pops are voltage spikes that indicate that a transistor\IC is breaking down and will eventually short. Good luck!

barneyluc

Oct 01, 2008 | Audio & Video Receivers

1 Answer

My ma6100 amp will not put out you can hardley here it turned all the way up please help I miss my music.


check interconnect cables(from media source to amplifier input).
check speakers cables from amplifier out to speakers.
play different media sources(dvd-cd-vcr)and check.
apply a contact cleaner over volume control and move it in all directions.

Jul 22, 2008 | Audio & Video Receivers

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68301 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...