Question about Dell 5110cn Laser Printer

3 Answers

How to Replace Dell Fuser?

Hi,
I hope you are doing well.
If this color laser printer has the fuser on forward facing part of the printer. ( I forgot the model at the moment) Could tell me or send a URL on how to replace the fuser?
In advance, "thanks" for your help.

Best regards,
Paul M

Posted by on

  • Anonymous Jan 19, 2009

    How long the fuser last! How many copies?

    Claude.

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

How do you reset fuser on a dell 5110? replaced fuser but still tells me to replace

Posted on Jan 11, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 188 Answers

Hi Paul,

If this is a 5100, then the replacement of the fuser is quite simple.

1) Before removing the fuser:

  • Disconnect the A/C power cable from the back of the system.
  • Press the right side latch button, and then rotate open the outer duplex assembly.
How to Replace Dell Fuser? - caution.gif CAUTION: The fuser reaches extremely high temperatures during operation. Allow for adequate cooling time after the printer is powered off, before removing the fuser.
2) Lift the two fuser assembly locking levers.
9323b49.jpg
3) Grasp the two fuser handles, and then lift the fuser out of the chassis.


5acd3b0.jpg

Posted on Oct 22, 2008

  • Cory Friedman
    Cory Friedman Oct 30, 2008

    i am glad i was able to help :)

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Director Badge:

    Uploaded 100 video answers.

  • Expert
  • 160 Answers

Here is a video explaining how to install the 5110 Fuser. To anyone doing this remember that the 5100 and the 5110 fusers are different and although they look similar they are not compatible.

Posted on Jun 27, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reset fuser message on dell 5130


Johnathan, Reset the life counter:
  1. Enter the printer's tech mode by quickly pressing the sequence of keys Menu > Up Arrow > Left Arrow > Tick > Right Arrow > Cancel > Menu. If tech mode does not appear, Re do key sequence again as quickly as possible. A delay in pressing the keys will stop the menu from opening.
  2. Select tech menu , data setup, Clear fuser count.
  3. Restart the printer.
  4. Check the attached links,instruction and guides, Good luck
    "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Knowledge Base

Replacing the Fuser on Dell 5130cdn Laser Printer

https://www.sosnfl.com/wp-content/uploads/2014/12/Dell-5130cdn-Users-Guide.pdf

Apr 09, 2016 | Dell 5130cdn Color Laser Printer

1 Answer

How to replace fuser in Dell 1135N printer


Hi,
Contact nearest Dell printer technician Center or Dell customer service center. If not available then visit this link i hope solved your issues.
Read More...Dell Printer Support

Thanks,

Jul 23, 2014 | Dell 1135n AllInOne Laser Printer

1 Answer

Removal of paper stuck in a dell 3115 fuser?


It's best to remove the fuser to get access to it. This video will show you how to remove it, and which levers to move to release tension in the pinch roller to clear the jam http://www.youtube.com/watch?v=UjyggtF8d1k After you remove the jam make sure to do a close inspection on the internal roller (use a flashlight). You're looking for any scratches or "dents" in the colored roller (sometimes a deep red/brown color sometimes blue) if there are scratches you are probably going to have to replace the fuser. The imperfections on the fuser roller will show up on your printed pages. If you do need a new fuser you can find them for $160, or the entire rebuild maintenance kit for $375 http://www.fastprinters.com/productdetails.asp?PRODUCT_ID=DELL-UG190

Dec 19, 2013 | Dell Printers:Dell MFP Color Laser 3115cn

1 Answer

Reset fuser reading in window display what should I do


Open the fuser door and pull the fuser unit out, top of printer or top rear. Should see 2 oval looking handles I believe they are blue, grab the handles and pull the fuser should pull straight out. Then re-seat it back in to printer. And by the way do this procedure while the unit is sill turned on.

Jul 31, 2012 | Dell 2130cn Laser Printer

1 Answer

Error 010-297 restart printer


Hi belljohnson5,

The code is caused by a small switch under the fuser unit not sensing the fuser unit is in place. The blue plastic locking tab on the left side of the fuser has a small catch on the bottom of the fuser. The catch is supposed to slip thru a space in the steel plate under the fuser unit and secure the fuser in place. As the catch slides forward under the steel plate, it pushes on the trigger of the sensing switch, closing the sensing switch and letting the copier know that the fuser is in place. (there is also a similar locking tab on the right of the fuser but it doesn't trigger a sensor like the left one does) 1) The fuser gets very Hot!! Let cool for 10 minutes after turning off the power and unplugging the copier! 2) Pull the two blue locking tabs forward and remove the fuser unit. Reinsert and push back on the tabs to lock back into place. Sometimes just reinserting the fuser will allow the catch on the locking tab to function correctly and push the trigger on the sensing unit. Turn the copier back on and pray the error code doesn't reappear.. 3) Mine reappeared. Evidently the catch on the fuser unit was still not pushing the trigger forward, causing the copier to surmise that no fuser unit was installed. At this point, you should buy another fuser unit or take your copier to an authorized Dell repair center.

Hope this helps.

Thank you for using FixYa.

May 05, 2010 | Dell 3100cn Laser Printer

1 Answer

My laser printer gives message open heat error how can I fix


This is most commonly caused by a failure of the Fuser unit.
However, in rare circumstances, this can be caused by the Fuser Control section of the SMPS, or the fuser temperature monitoring circuit on the Main Board.
There is a closed control loop:
1. AC voltage is supplied to the Heat Lamp in the Fuser from the Fuser Control section of the SMPS
2. The temperature of the fuser heat is monitored by a thermistor (mounted on the Fuser) connected to the Main Board.
3. The Main Board determines if the fuser temp is too low, correct, or too high and signals the Fuser Control to increase, maintain, or decrease the AC voltage to the Fuser
sorry io say but you had to replace the fuser
call dell costumer support and tell your model no. ask for fuser replacement and they will do it .
Hope your printer is in guarantee period otherwise you had to pay.
REGUARDS

Dec 13, 2009 | Dell 1600n All-In-One Laser Printer

1 Answer

Error code 010-397 dell printer 5100. Have change fuser and restart printer keeps coming up as error message


) The fuser gets very Hot!! Let cool for 10 minutes after turning off the power and unplugging the copier!

2) Pull the two blue locking tabs forward and remove the fuser unit. Reinsert and push back on the tabs to lock back into place. Sometimes just reinserting the fuser will allow the catch on the locking tab to function correctly and push the trigger on the sensing unit. Turn the copier back on and pray the error code doesn't reappear..
3) Mine reappeared. Evidently the catch on the fuser unit was still not pushing the trigger forward, causing the copier to surmise that no fuser unit was installed.

CBR Tech Solutions or http://www.cbrtechsolutions.com

Oct 14, 2009 | Dell 5100cn Laser Printer

2 Answers

Our HP Color Laser Jet Printer keeps saying 50.2


Hi ellenf971:
Here is your problem.
50.X FUSER ERROR
50.2 error - Fuser Failure (Abnormal Warmup).
Perform the following steps:
1. The connector between the fuser and the
printer is not connected properly. Reseat
the fuser. Check the connector J5013
between the fuser and the printer. Replace
it if damaged.
2. Break in the main thermistor. Turn the
printer off and remove the fuser. Measure
the resistance between the fuser
connectors J5013LA-2 (MAINTH) and
J5013LA-1 (GND). If it is not within the rage
of 330k ohms to 50k ohms (at ambient
temperature), replace the fuser.
3. Break in the fuser heater. Measure the
resistance between the fuser connectors
J5013L-2 (FSRH) and J5013L-1 (FSRN)
with the fuser removed. If it is not within the
rage of 12 ohms to 52 ohms (at ambient
temperature), replace the fuser film unit.
4. Faulty DC controller. PCB Replace the
DC controller PCB
you will have to get an HP certified technician to replace the fuser assembly.

Hope this helps

Jul 17, 2009 | HP Office Equipment & Supplies

1 Answer

Changing the fuser unit


1 Unplug the power cable.
2 Remove the paper delivery tray assembly
3 Remove two (2) screws from the right cover assembly
4 Remove the right cover assembly, carefully disengaging the catches
5 Unplug the control panel cable.
6 Insert a screwdriver to loosen the release tab on each side of the upper face cover
7 Remove the upper face cover
8 Remove four (4) screws from the upper cover
9 Lift up and remove the face-down cover
10 Remove the output tray by releasing the tabs.
11 Unplug the harness from the fuser motor
12 Open two (2) clips and remove one (1) clip to remove the fuser connector.
13 Unplug two (2) 3-pin optical encoder wires
14 Unplug the red high-voltage bias wire.
15 Remove the thermistor wire.
16 Remove the cables from the wiring harness.
17 Remove three (3) screws from the fuser chassis.
18 Gently rocking if necessary, roll the fuser forward to remove.
Use the following procedure to replace the fuser.
1 Align the fuser tabs with their respective holes.
2 Complete replacement by following steps 1 through 18 above in reverse order.
NOTE When replacing the right cover, align the tabs on the upper edge of the right cover
and lower edge of the face-down cover with their respective slots.
Hope this helps

May 16, 2008 | HP Color LaserJet 2600n Printer

Not finding what you are looking for?
Dell 5110cn Laser Printer Logo

Related Topics:

4,305 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dell Office Equipment & Supplies Experts

Prashant  Sharma
Prashant Sharma

Level 3 Expert

1127 Answers

The Knight
The Knight

Level 3 Expert

69795 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6370 Answers

Are you a Dell Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...