Question about Proscan PS32108 32" TV

1 Answer

Picture width is too large for my screen

I have a ProScan 32" tv (10+ years old). Lately, the picture displays too wide for the screen. How can I adjust the picture size to fit the screen?

Posted by on

  • Anonymous Feb 22, 2009

    I have the same problem with a Phillips tv. There is no setting to adjust horizontal/vertical control.

  • Anonymous Mar 13, 2009

    Picture width is too large for my screen...how do i fix it???

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 84 Answers

Look for horizontal control

Posted on Oct 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No picture


The main problem is from theTV menu.I would recommend you press,menu,then settings,then display settings,and last tv screen. After, you'll get options on how you want to make your screen look like.Example:wide screen, Automatic, etc.

May 31, 2010 | GE 32GT740 32" TV

2 Answers

We have a 32" standard sharp tv about 10 years old and we are having trouble with the picture. There are colored dots all over the screen.


Dear sir,your television is very old ,so picture tube is weak for this reson color dot all over the screen, replace the tube then is ok.

Nov 23, 2009 | Sharp 32C-240 32" TV

1 Answer

My proscan tv went into wide screen....everything shows up bigger. how do I get it back to normal? By wide screen, I mean if there are 2 people sitting at a table talking on screen at opposite sides of...


It sounds like you accidentally enabled a zoom feature or something similar.

Most remote controls should have a clearly labeled "zoom" button or a "picture size" option. If not, go into your TV's menu and look for something zoom related.

If this doesn't work, just go ahead and toy around in your TV's menu. I strongly suggest writing down the default settings so you can go back to them if you screw something up.

Good luck!

Aug 27, 2009 | Proscan Standard (CRT) Televisions

1 Answer

Distorted picture on my 32" Proscan TV...(about 15 years old)


The RCA GE sets have a problem with bad solder connections in the tuner unit which also causes numerous symptoms including poor regulation, no vertical deflection, low audio or dead set.

Pulling in from the sides is either poor regulation or a bad eeprom/solder join issue

Mar 13, 2009 | Proscan PS36123 TV

1 Answer

Proscan ps35653 chassis ctc169 picture to wide for screen


press the menu button on the front of the tv and then scroll down using the channel buttons to picture format, next change the format from widescreen to standard.

Jan 19, 2009 | Proscan PS36123 TV

1 Answer

TV picture won't open.


The vertical sync circuit has gone bad...you'll have to have it repaired if you want to keep it

Jan 03, 2009 | Standard (CRT) Televisions

1 Answer

Picture to wide


This trouble symptom picture wide or"blooming", the picture becomes dim even with the brightness control full on,and there is an abnormal enlargement of picture or raster.Usually,the enlargement is uniform,but there may be some defocusing.In some circuits,the brightness control operatesin reverse(rotating the control for an increase in brightness produces a decrease) after reaching a critical point on the control. If the picture wide is not accompanied by insufficient width(a symptom of horizontal output failure) the probable cause is a high volatge circuit ony,particularly the HV rectifier and HV winding.Any circuit problem that reduces but does not completely eliminate the high-voltage output to the picture tube second anode can cause overscan. The most likely defects are leaking high-voltage capacitors,defective high voltge tube rectifiers,leaking high voltage leads,defects in high voltage circuit protective resistance,and shorted turns in high voltage winding of the flyback transformer.

Hope this may help you;

DON'T FORGET TO RATE:

Regards,

Sep 06, 2008 | Toshiba 32AF45 32" TV

1 Answer

Vertical line picture


problem is caused by the loss of horizontal deflection signal. It is quite surprising that the entire unit is still working, since usually, a loss of H-Out will disable the entire set. Problem can be as simple as loose solder connection to a more complicated defective horizontal circuit. I would suggest havint it checked by a professional TV tech.

Jul 16, 2008 | Proscan PS36500 36" TV

2 Answers

3 inches missing on both sides


Sounds like it is a widescreen TV stuck in standard view mode. Should have a menu option called widescreen or movie format.
Do you see the whole picture squeezed down or is it actually cutting off the sides of it?

Jan 08, 2008 | Proscan PS32125 32" TV

1 Answer

Screen Widens Out Constantly


you might be getting more supply from regulated power supply if you get wide pictureor width have to be adjusted by width control. but if it stretchs out & lose some of the picture on the right and left edges it might be due to horizontal output section. 1 loose contact in connector. 2 some capacitor might be defective in h/section caution please do not open the set unless you know about high voltage in tv set.

Sep 16, 2007 | Emerson EWF2703 27" TV

Not finding what you are looking for?
Standard (CRT) Televisions Logo

Related Topics:

893 people viewed this question

Ask a Question

Usually answered in minutes!

Top Proscan Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68352 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Cindy Wells

Level 3 Expert

4759 Answers

Are you a Proscan Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...