Question about Jenn-Air WW30430P Stainless Steel Electric Double Oven

1 Answer

Jenn-Air Wall Oven Model #WW30430P F5 Fault Code

The upper oven in my double wall oven (see above model number) started to preheat, then began beeping and displaying an F5 Fault Code. To stop the beeping, I have to turn the oven off. The lower oven seems to be working fine. Is this something I can fix myself and, if so, could I please get some instructions? Thanks.

Posted by on

  • MissingLinks Oct 24, 2008

    An update on the problem above. I replaced the clock part as indicated by the F5 fault code. Oven is STILL not working and is displaying an F3 fault code. Since the first part cost nearly $200, do I want to continue with this process or just scrap the stupid oven? (Jenn-Air is ****.)

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the exact same problem with an F5 fault code. I also have a new clock assembly. RepairClinic.com said "Jenn Air fault code F5 = Hardware and watchdog circuits disagree / Replace clock assembly (also called the ERC)

Jenn Air Fault code for newer models F5 = Power to element relays disabled in cook mode
1. Intermittent oven temperature sensor or wire harness or,
2. Intermittent contact on power relay board"
This doesn't help since it is too technical. What should I do next?

Posted on Jan 15, 2010

  • Jian Wu Dec 09, 2013

    I have the same exact issue with the Jenn Air double oven, believe to be the same model. the upper one stops working and gives code F5 and the bottom works... Did you eventually fix the issue? Thanks you.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the Start Amprege for a Jenn Aire #WW30430P


phone jen air tech support daytime Eastern Standard time:
1-800-JENN-AIR (536-6247)

Dec 20, 2013 | Jenn-Air WW30430P Stainless Steel Electric...

1 Answer

Jenn Air wall oven won't cancel / shut off . Recently replaced membrane.


Hey - the ribbon link from membrane to control is a tricky plug to get in right- double check this connection and let me know if it helps- Thanks- Ed

May 13, 2010 | Jenn-Air WW30430P Stainless Steel Electric...

1 Answer

F1 error code and constant beeping and oven shuts off.


Hi gwhiz03,

If you are having error code F1 with your Jenn-Air double wall oven this is because you have a defective touch pad or clock (ERC). This simple test will help determine whether the ERC (Electronic Range Control or Clock) or the touch pad is defective when F1 error code is present.

Note: Some models incorporate the touch pad in to the ERC as a single assembly, in which case this test is not necessary. Simply replace the ERC (Clock).

Warning: If you feel in any way uncomfortable performing this test or making this repair, please contact a qualified appliance repair technician.

1. Disconnect power to the range (unplug the range power cord or turn the power off to the range at the circuit breaker). It is very important that the power to the range has been disconnected, so please double check before continuing.
2. Gain access inside the control panel.
3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC.
4. Make sure there are no lose wires, or anything else that may cause a short when power is turned back on. Assemble the control panel back the way it was.
5. Turn the power back on.
6. Wait for at least one hour to see if the F1 code comes back (usually accompanied by a beeping sound).
7. If F1 comes back, replace the ERC. If it does not, replace the touch pad.

Hope this helps.

Thank you for using FixYa.

Feb 10, 2010 | Jenn-Air WW30430P Stainless Steel Electric...

1 Answer

The control panel display light is completely dark but the oven still seems to function ok. Jenn Air Model WW30430P double wall oven.


A lot of ovens use a gas-filled vacuum flourescent display module that takes a higher voltage to drive it. The modules can get damaged or the power supply for the higher voltage (usually around 50 volts) may have failed.

Chances are the thing is only sold as an assembly...While the displays are common in auto speedometers that have digital display, those for these ovens are special with wpecial characters and background.

Jan 31, 2010 | Jenn-Air WW30430P Stainless Steel Electric...

1 Answer

Am negotiating a home inspection on a house with WW30430P Jenn Air Wall Ovens; neither of the doors close. Is there a solution?


There are several models of Jenn-Air ovens that had issues with the door closing. The only solution is to replace the door hinges (unless the doors themselves are bad, you can see this if you open the door, the porcelain on the door will be bulged and cracked right where the hinge joins the door). If the doors are bad, the hinges and the interior door panels need to be replaced. Hope this helps!

Dec 16, 2009 | Jenn-Air WW30430P Stainless Steel Electric...

1 Answer

F2 code


F-2 error for jenn-air means the oven is to hot, it could be the oven temperature sensor is faulty, or the relay board.

Mar 29, 2009 | Jenn-Air WW30430P Stainless Steel Electric...

1 Answer

Lower electric wall oven won't heat up


It is highly likely that your heating element is open so I would ( with power removed) verify the integrity of the element by detaching it and making sure it is not elecltrically OPEN, It is nothing more than a big power resistor that when current is flowing,..gets hot but if it becomes open.. you will not have any curent flow thru it ( or heat generated from it). That would be the first place I would look.. It could also be the control that feeds it..
A few ideas to check..
Regards,
Rick

Feb 15, 2009 | Jenn-Air WW30430P Stainless Steel Electric...

3 Answers

Problems with Jenn-Air Electric Double-Wall Oven


that board supplies power to the light unit and it is very easy to replace if that is what is wrong. it can also be the led display unit also. cost about $150 each i think.

Oct 26, 2007 | Jenn-Air WW30430P Stainless Steel Electric...

Not finding what you are looking for?
Jenn-Air WW30430P Stainless Steel Electric Double Oven Logo

1,134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jenn-Air Ovens Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

 Fix Your Board
Fix Your Board

Level 3 Expert

310 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Are you a Jenn-Air Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...