Question about Dryers

1 Answer

WTV74307GB hi i have bosch exxcel dry, and i keep getting the filter light coming on, i have cleaned the filter and replaced it, but the dry stop again after some time., can you help I have exactly the same problem - the dryer has never worked properly since its delivery 2 weeks ago - I have tried everything which might be the cause and nothing has worked. It dries for about 15 minutes, then the display shows ---- and the filter light blinks. The filter is as good as empty though. I get my washing dry by running downstairs every 20 minutes to switch the dryer back on. I am extremely frustrated.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 550 Answers

The warning does not strictly mean filter only
there is a lint blockage somewhere in the vent system and there is only a single response the dryer knows to make
fan
fan housing
duct
outside vent
could all be sufficiently blocked to set off the warning

Posted on Oct 19, 2008

  • AlmostBob
    AlmostBob Oct 19, 2008

    'specially if the install was done to the prior ducting without cleaning it out

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heat problem


Sound like thermostat is not working. Should turn off heating elements when drying temp. is reached.

Jan 20, 2014 | Bosch Nexxt WTMC 3300 Electric Dryer

1 Answer

On my Bosch Nexxt 500 Series Electric Dryer keeps shutting off and gives the E-01 error we have check the exhaust air duct on back of the dryer and we have vacuumed the inside bearing shield what else...


Motor won't work
Lint screen hi-limit (thermal cutout) tripped.
Clean lint screen and clean lint and other debris from front shield, then replace hi-limit. Also check exhaust duct length & # of elbows.
Wire harness failed.
Run resistance or continuity checks to track down broken wire or connector. Replace failed wire harness.
Display shows "E:01" during drying.
Lint filter, air duct or air damper is blocked.
Air leaking past felt drum seal.
Air duct is too long, too small or has too many bends. Inadequate ventilation around dryer (i.e. in a closet).
Clean out filter, air duct and air damper.
Replace felt drum seal. If seal doesn't fit snugly onto drum, wet felt and dry it by running a timed dry cycle for 20 minutes (felt will shrink and fit drum snugly).
Shorten, enlarge, reroute and reduce # of bends in air duct. Move dryer to an area

Jan 09, 2011 | Bosch Nexxt 500 Dryer

1 Answer

Hi! I have a new Bosch Dryer. We can't seem to get it to dry. It stops after just a minute with a linter filer light flashing.


i take it you have cleaned the lint filter if so then it has a bad sensor reader in the filter system

Dec 22, 2010 | Bosch WTMC3510UC Gas Dryer

1 Answer

After one load, dryer stopped working. lint


With the exhaust clear, you need to be sure that air is actually moving. It could be a bound or bad exhaust blower.

Mar 28, 2010 | Bosch WTMC3500UC Gas Dryer

3 Answers

Bosch Axxis Starts and stops


The lint light keeps coming on and shuts the dryer off so clothes are not dry. I checked the filter and it is clear. Now the bottom of filter is cracked (plastic part) so I need to replace. But why does the lint light come on now after 5 years of use? It never came on before even when the lint filter was full?

Apr 20, 2009 | Bosch Axxis WTA 3510 Electric Dryer

1 Answer

Filter light flashing on bosch exxcel condenser, repeatedly.


This should help you find a manual.
http://www.managemyhome.com/mmh/products/ManualSearchDisplay.action?psid=31378668&sid=MMHSx20070515x00001a

Tip: Always provide the complete information provided on the manufacturers product information data tag, located on the unit, and not in the user’s manual. This will help you acquire a more accurate and expeditious response to your complaint.


If my assistance helped resolve this issue, please show your appreciation by rating how effective my advice was in resolving this issue.
Thank you,
Dave E. (Illeagle)

"Your satisfaction is my personal reward"

Jun 19, 2008 | Dryers

3 Answers

Bosch maxx wtl 6300 dryer when placed on a dry cycle it beeps every couple of minutes and stops and the filter light flashes. The lint filter is cleaned and it still does this any help?


Hi Guys...
At least I can shed some light on how to open the bottom part.
When you are looking into the dryer with the door open, take a look at the bottom hinge of the door. There is what looks like to be button popped out slightly.. 
Place your thumb on it and press. This should open the bottom part of the dryer.  Then clear out the gap between where the lint filter connects to the other units below it (when the door is closed...)
Hope this makes sense... there seems to be a sensor there..  I just cleaned mine so praying that the beeps stop.. Its been driving us mad for the last 8 months!

May 14, 2008 | Dryers

1 Answer

WTV74307GB


take the lint screen out and clean it with a toothbrush and warm soapy water. You may be using too much softner. If that doesnt work, the control board may be bad.

Mar 30, 2008 | LG DLE2514 Electric Dryer

2 Answers

Bosch Axxis WTL 5400 Electric Condensation Dryer...Lint Filter Light


have you checked the vent line it could be stopped up if the line is bent same affect as the lint filter being full

Dec 15, 2007 | Bosch Axxis WTL 5410 Electric Dryer

7 Answers

Bosch Dryer lint filer warning


The Bosch Dryer has a temperature probe in the heater exit and in the exhaust area visible when you open the door. If the temperature difference between the two gets to high, the lint filter is assumed to be plugged and the alarm goes off.

It seems that the temperature probe at the heater, can end up with a faulty connection to the control panel over time due to corroded contacts or lint build up. When this happens the control panel thinks the filter is clogged and it may also not turn on the heating elements properly. Remove the back cover over the heating element (12 screws) and then remove the one screw holding the red wiring connection to the dryer body. You can then wiggle out the wiring connection and clean / unplug and replug in the connector for the sensor. (plug with two small wires only). A little hard feeding the connector back through the hole so take your time and don't damage the wires). Should all work again. May want to inspect inside the heater at same time and make sure the overheating switch is not tripped. ( press in the red button).

May 21, 2007 | Bosch WTMC3510UC Gas Dryer

Not finding what you are looking for?
Dryers Logo

Related Topics:

252 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...