Question about Whirlpool 24 in. GU3200XTP Built-in Dishwasher

4 Answers

Whirlpool dishwasher reset code

Whirlpool dishwasher model#: (DU1050XTPB3).

my dishwasher seems to be locked up and needs to be reset. the clean led is constantly flashing. i had this trouble in the past, and the serviceman reset the dishwasher by using the touchpad on the front as a code and washer worked again. do you know the code.

Posted by on

  • parts4less May 05, 2009

    my whirlpool dishwasher is in lock mode, on the front of the dishwasher is a symbol of a lock with a light above it witch is on. the machine opens up, just will do nothing

×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Yup, found it on another site..I had the same issue today.

Reset code: Push 1. Heat Dry 2. Normal 3. Heat Dry 4. Normal

wait about 2 minutes as the controller resets itself. You should see all the leds flash on and then wash and rinse leds stay on for about 30 seconds. A minute or so later ..presto, my machine worked again.

My machine is not the GU3200XTP, but in the same Whirlpool tall tub series (same manual) so leds may not have the same name.

Mark

Posted on Oct 21, 2008

  • 2 more comments 
  • susieq69 Nov 13, 2012

    thanks it works my dishwasher was flashing clean i took it apart cleaned it than put it back together then reset it work better then ever thank you

  • James
    James Apr 25, 2013

    the reset worked with ours :)

  • James McCarter Sep 08, 2013

    Reset worked, but this is the second time I have had to do it. Any ody know what is causing the lockup?

  • marilyn bailey
    marilyn bailey Feb 11, 2016

    THANK YOU THANK YOU THANK YOU!!! Was ready to call a service person and/or buy a new dishwasher...but this worked perfectly! All seems to be working fine...now!

×

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Reset code: Push 1. Heat Dry 2. Normal 3. Heat Dry 4. Normal

Posted on Dec 22, 2010

  • James
    James Apr 25, 2013

    the reset worked with ours :)

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Whirlpool Dishwasher GU2400XTP B1 problem... starts & runs fine until it reaches the HEAT DRY cycle. Then it shuts off, clean LED is flashing.. I've tried the reset code (HD<N<HD<N) it will reset the dishwasher & goes into the rinse cycle again. Unit will NOT get dishes clean NOR will it dry them.. any suggestions ???

Posted on Mar 06, 2009

  • Jesster May 18, 2013

    Don't ever buy a whirlpool (or Maytag) product ever again. That is the easiest way to not have that problem again. I talked directly to an administrative assistant at corporate and she said that dishwashers and washing machines only last about 5 years from the maytag dependability people. Our old maytag lasted 13 years with one pump replacement. Our current 6 year old just got its third pump replacement. Our old maytag washing machine lasted 19 years. Our current 7 year old maytag washer has had the tranny replaced and the timer switch replaced. I can only say, based on my experience with whirlpool brands; they have implemented planned obsolescence across the brands they sell. I will never buy whirlpool again!

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 128 Answers

If you pull your dishwasher apart first take out silverware holder then bottom holder then top but the top you have to take out two clips at the end of the track then it slides out next the water jacket on the back its two phillips screws then twist off the spinnner at the bottom of dishwasher thenthere is 4 torx screws pull up then you see one more torx pull off cover an that should be your problem you need to clean that out i clean mine every two months my thinks its a garbage diposal

Posted on Aug 19, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Whirlpool Dishwasher DU1300XTV


Heating element goes bad causing the controller to go bad as well

May 14, 2014 | Whirlpool DU1300XTVQ Dishwashers : Built...

4 Answers

Whirlpool GU1200 XT Dishwasher Will not


Press the [Menu] Soft key in standby mode and press
[*] key within 3 seconds to lock the keypad. Keypad lock
remains unlock if [*] is press after 3 seconds.

May 30, 2008 | Whirlpool Dishwashers

1 Answer

I need the reset codes for my dishwasher. It gets stuck in demo mode at times. That's what the repair man said who came last time. My dishwasher is the Whirl Pool Quiet Partner I, Model Number...


Hi, this is the reset code: Push/Press 1. Heat Dry 2. Normal 3. Heat Dry 4. Normal

Wait about 2 minutes as the controller resets itself. You should see all the leds flash on and then wash and rinse leds stay on for about 30 seconds. A minute or so later it will start working....

Jun 11, 2011 | Whirlpool 24 in. DU1055XTP Built-in...

1 Answer

My dishwasher seems to be locked up and needs to be reset. the clean led is constantly flashing. i had this trouble in the past, and the serviceman reset the dishwasher by using the touchpad on the front...


Control is programmed to
stop the current cycle and
not allow any further
cycles if it suspects a
faulty heater (no
temperature increase
detected in heated
intervals). Control blinks
the Clean LED 7 times in
repetitive fashion and
disables the Start/Resume
key until cleared.
Heater circuit problem:
■ Open in heater.
■ Open connection or
component in heater
circuit.
■ Faulty heater drive
circuit on control.
Running Diagnostics clears the control and
allows it to operate again. If heating problem
is not corrected though, the control will stop
running again on next cycle. See below.
1. Unplug dishwasher or disconnect power.
2. Check all components and connections in
the water heating circuit or heat dry circuit.
■ Check resistance of heater.
■ Check resistances of all connections and
components between the control and
heater.
■ Check operation of heater and temperature
sensor in Diagnostics cycle.

Aug 26, 2010 | Whirlpool 24 in. GU3200XTP Built-in...

1 Answer

My dishwasher is a whirlpool model # DU1050XTPB3. The clean button keeps flashing and when I push the start button nothing happens


The blinking clean light is an interruption in the dishwasher program that usually indicates a component malfunction. This can also be a result of a momentary program glitch. If a component is defective, it's usually attributed to the heating cycle or thermostat failure. To rule out component failure, or program error, the following link explains how you may be able to clear the blinking clean light problem and possibly avoid a service call:

http://www.fixya.com/support/r3575752-dishwasher_blinking_clean_light

Keep in mind all dishwashers are not alike and have different panel options. If you do not have the same set up that I have mentioned, the tech sheet for your dishwasher will explain the touch pad functions. The tech sheet is located behind the lower toe panel under the door and lists the proper sequence of buttons to push for diagnostics and troubleshooting. Just remove the screws that hold the panel in place and remove.

NOTE: Sometimes the tech sheet is located behind the inner door panel. You will need to remove the screws securing the inner panel to access it if this is the case. Make sure you turn off the main power breaker before doing so.

In many cases, I found this to be a momentary glitch in operation. If the problem keeps reoccuring the number of flashes is an indication of WHICH circuit is causing your problem. As all dishwashers differ in operation and features, refer to your tech sheet for the recommended troubleshooting steps.

NOTE: Some dishwashers use the Sani-Rinse/Air Dry combination, some use the Sani-Rinse/Heated Dry combination. Some use a sequence of three, others use a sequence of 5 pushes of the buttons. If the tech sheet is not located behind the lower toe panel, it should be affixed somewhere under the dishwasher. I have also found them located inside the inner door panel. Please post back and let me know if you still need assistance.

Jun 24, 2010 | Whirlpool 24 in. DU1050SS Built-in...

1 Answer

Clean light is flashing du1145 whirlpool dishwasher, will not run


Hi,

This is a Common Problem. Read the same solution i offered to many Customer's and it actually worked like anything :-

Hi,

This machine was made by Whirlpool and the flashing clean light is a common error code for them.
If the clean light is the one flashing then your dishawasher could have a heater circuit problem (depending on the age) or this could simply just be water colder than it is used to getting.
Repeatedly press the Heated Dry and Hi-Temp Wash(scrub) which ever yours has untill all the LED lights come on, press cancel twice and try the dishwasher again making sure to run the water at the kitchen sink till it is hot before starting the dishwasher, if this trips and locks you have a problem with the heating element, or temp sensor.
Press the heated dry button followed by the normal cycle button, and then repeat once. You should see all of the lights come on for a second or two, and then the dishwasher will work again.
If you haven't already, take a look under the kick plate in front to see if there is a schematic tucked in there somewhere. Whirlpool has put their diagnostics for specific models on these.
I don't have the specific repair manual for you model.
So, if the above combination does not work here are two more that have worked for me.
HiTemp Wash + Air Dry + HiTemp Wash + Air Dry in less than 5 sec
or
Hi Temp Scrub/Scour + Air Dry + Hi Temp Scrub/Scour + Air Dry in less than 5 sec



Let me know, if you need further assistance.


Hope i helped you.


Thanks for using ' Fixya ' and have a nice day!!

Jan 11, 2010 | Whirlpool Dishwashers

1 Answer

Dishwasher will not run clean light keeps blinking


Hi,

This machine was made by Whirlpool and the flashing clean light is a common error code for them.
If the clean light is the one flashing then your dishawasher could have a heater circuit problem (depending on the age) or this could simply just be water colder than it is used to getting.
Repeatedly press the Heated Dry and Hi-Temp Wash(scrub) which ever yours has untill all the LED lights come on, press cancel twice and try the dishwasher again making sure to run the water at the kitchen sink till it is hot before starting the dishwasher, if this trips and locks you have a problem with the heating element, or temp sensor.
Press the heated dry button followed by the normal cycle button, and then repeat once. You should see all of the lights come on for a second or two, and then the dishwasher will work again.
If you haven't already, take a look under the kick plate in front to see if there is a schematic tucked in there somewhere. Whirlpool has put their diagnostics for specific models on these.
I don't have the specific repair manual for you model.
So, if the above combination does not work here are two more that have worked for me.
HiTemp Wash + Air Dry + HiTemp Wash + Air Dry in less than 5 sec
or
Hi Temp Scrub/Scour + Air Dry + Hi Temp Scrub/Scour + Air Dry in less than 5 sec



Let me know, if you need further assistance.


Hope i helped you.


Thanks for using ' Fixya ' and have a nice day!!

Jan 10, 2010 | Whirlpool Dishwashers

1 Answer

Whirlpool quiet partner 1 # DU1055XTSQ2


Read this article, it should address your problem.

http://fixitnow.com/wp/2006/03/20/whirlpool-built-dishwasher-includes-kitchenaid-and-some-kenmores-wont-start-clean-led-blinks-seven-times/

http://tclaundryrepair.com/

Feb 24, 2009 | Whirlpool 24 in. DU1100XTPS Built-in...

2 Answers

Model # DU1055XTPQ3 WHIRPOOL DISHWASHER RESET CODE


chris72 had the solution to my Whirlpool DU1055XTPQ3 not turning on. Per Chris's suggestion, I pressed back and forth between sani rinse and heated dry. All the lights came on as it reset and it was good to go. The dishwasher started up immediately. Saved me a service call, THANK YOU Chris!!

Aug 07, 2008 | Whirlpool 24 in. DU920PW Built-In...

6 Answers

Kenmore 66516032400 Dishwasher


On another website, we found a reset code that works for our Kenmore, which I think is the same as yours. Hit Heated Dry, Normal Wash, Heated Dry, Normal Wash (one at a time, within six seconds).

Dec 05, 2006 | Kenmore 24 in. 16032 Built-in Dishwasher

Not finding what you are looking for?
Whirlpool 24 in. GU3200XTP Built-in Dishwasher Logo

19,009 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Mike

Level 3 Expert

4336 Answers

Owen Barnes

Level 3 Expert

867 Answers

yadayada
yadayada

Level 3 Expert

74688 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...