Question about Onkyo TX-SR601 Receiver

1 Answer

Standby button stuck

Onkyo TX SR601 - standby/on button stuck in standby position - can't turn machine on

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 142 Answers

Hello. Check all of the buttons on your unit to make sure that they are not stuck...you can feel the click they make as you push it then they pop back out as your finger pulls off. Any stuck button will lock up your microprocessor and keep the unit from turning on. All other problems will require a consumer electronics technician to trouble-shoot the turn on circuit. If you know how to use a meter and know how to solder\unsolder and require further assistance you can contact me. Good luck.

barneyluc

Posted on Oct 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No power for onkyo tx-sr601


C7524 = 0.1F

Onkyo 3000120 or FMC0H104Z

Oct 04, 2012 | Onkyo TX-SR601 Receiver

1 Answer

Onkyo sr600 memory problem


I had the same problem with my TX-SR601 receiver.
Solution: I changed the capacitor C766 (100uF/6,3V) on the "DSP and main microprocessor" or "U1" board. This capacitor is responsible to keep the settings in the memory. It is directly next to the SRAM ICs (Q705-706) (type: CY7C1019BV/CV33-15VCT).
Now the receiver works properly again.

Mar 04, 2012 | Onkyo TX-SR601 Receiver

1 Answer

Message states the power to zone 2 is not activated when trying to listen to zone 2 speakers. Nothing in my manual about this message. How do I activate power to zone 2 on a tx-sr601


Page 77:

"Not available in Zone 2 mode" Setting not allowed because the Zone 2 mode is turned on.

"Zone 2 is not On" Will not work because the Zone 2 has not been turned on.

TURN ZONE 2 ON.

Register and download the manual for free at retrevo.com

http://www.retrevo.com/support/Onkyo-TX-SR601-Receivers-manual/id/365ag212/t/2/

Page 55 shows the prerequisite settings for using the surround back terminals for Zone 2.

Page 60 describes USING Zone 2 and points out that only analog sources can be used with Zone 2. Are you trying to use digital sources? Read the notes regarding REC OUT.

Jul 07, 2011 | Onkyo TX-SR601 Receiver

1 Answer

This site said it was free - then there is a charge? I am getting a "Protecting" message when I turn on my receiver - then it shuts off....What does this mean and what should I do?


It means the receiver senses excessive heat, or a short at its outputs. Disconnect the speaker wires and see if that helps. If not, get it to a Tech. If it turns on, figure out which speaker path(s) was causing the problem and resolve it.

The manual.

http://www.retrevo.com/support/Onkyo-TX-SR601-Receivers-manual/id/365ag212/t/2/

Power shuts off immediately after power on.

• Amplifier protection circuitry is activated. Remove the power cord from the outlet immediately. Contact your Onkyo service center.

Jan 13, 2011 | Onkyo TX-SR601 Receiver

1 Answer

How do I connect my Ipod to my SR601 Onkyo receiver?\r\nI am already using the CD and tape analogue inputs.


It will work with any Line Level input. The Front Panel Video 4 Input looks convenient.

Aug 12, 2010 | Onkyo TX-SR601 Receiver

1 Answer

How can I reset my Onkyo TX-SR601? Hard reset...


Hold Video 1 and Press the power button then turn it back on i had the same problem

Jan 07, 2010 | Audio & Video Receivers

1 Answer

Onkyo TX-SR601 6.1 Channels...dialog norm -3 readout


Enter the menu for speaker levels, and increase the center channel.

Dec 07, 2009 | Onkyo TX-SR601 Receiver

1 Answer

I blew a breaker and now I can't get my Onkyo TX-SR601, how do I reset


Are you referring to a system shutdown on the part of the Onkyo or a circuit breaker in your houses fuse panel / breaker box?

Aug 02, 2009 | Onkyo TX-SR601 Receiver

2 Answers

More watts needed


Add another power amp to line outs from your main amp to your speakers this will give more power(current) to your main speakers as you have decreased load on main amp

Dec 22, 2008 | Onkyo TX-SR601 Receiver

1 Answer

No receiver display lights


Hi ripper

The unit has a built in display dimmer, with a button to control the level of brightness from the display both on the remote, and the front panel.Try this

regards
Graeme

Nov 16, 2006 | Onkyo TX-SR601 Receiver

Not finding what you are looking for?
Onkyo TX-SR601 Receiver Logo

Related Topics:

717 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio & Video Receivers Experts

D. E. Hev

Level 3 Expert

1059 Answers

gbob59

Level 3 Expert

2963 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1042 Answers

Are you an Onkyo Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...