Question about Kenwood Car Speakers & Subwoofers

3 Answers

Hi i have a kenwood hdv 910 car sterio and i do not have the code key cod for it.

Posted by on

  • Nick Denovan
    Nick Denovan Oct 19, 2008

    hi,do you have the code

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 763 Answers

Sir is that the exact model of your car stereo? have you check the manual for it sir?


CHARCOIS

Posted on Oct 19, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 84 Answers

Type 1During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears. 
Enter the security code using your Kenwood remote. 
Type 2
Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear. 
Enter the security code using your Kenwood remote. 
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'. 
Enter the security code using your Kenwood remote.

Posted on Oct 19, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kenwood Master
  • 13,433 Answers

You can send your stereo back to Kenwood to have the security code reset.

Posted on Oct 19, 2008

  • Ekse Oct 19, 2008
  • Ekse Oct 19, 2008

    Note that you will have to contact your countrys kenwood support before sending anything. They will provide you with instructions.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to wire in a kenwood KDC-U456 to a xf falcon ute


If you don't have a schematic on the old radio the only way to be sure is check it with a multimeter , first identify your permanent power 12 volt DC then find your switched 12 volt this will turn on ansd off with your ign key , the earth cable is normally slightly thicker than the rest of the other wires in the loom and will normally be black or green yellow , you wil need to set your meter to ohms setting to identify the speakers you should get 3.8 to 4 ohms reading back from the speakers when you find them.

Apr 20, 2014 | Car Speakers & Subwoofers

1 Answer

Unlock code for Kenwood for MP 235 My remote does not work either. Is that because the unit is not unlocked?


Good Day,

KENWOOD SECURITY CODE CLEAR procedure

These codes are applicable for all Kenwood radios that do not have DVD or DVD screens located on unit.


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds

(so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio

stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key on the remote
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key on the remote

The security is canceled and the set enters the TUNER mode!

The above was pulled from:
http://forum.ecoustics.com/bbs/messages/4/134366.html

Hope this helps

Jul 05, 2008 | Kenwood Car Speakers & Subwoofers

1 Answer

I have a Kenwood KDC-MP235 Sterio and i cant figure out how to play an mp3 player ??


the mp refers to the fact that the radio will play cds burned in mp3 format. i don't believe you can connect an mp3 player up to it.

Jan 03, 2011 | Car Speakers & Subwoofers

1 Answer

Need security codes for kenwood KDC 4020


Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press and hold the "Auto" button and "Track up" (next track button on the right) on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

i hope this works for you.

Nov 26, 2008 | Kenwood Car Speakers & Subwoofers

4 Answers

I HAVE A 5 YEAR OLD KENWOOD KDC-x569. I have a new car I'm putting it in and just realized the security system has locked. It was so long ago I put it in I have no idea what the code is. Is there a way to...


Good Day,

KENWOOD SECURITY CODE CLEAR procedure

These codes are applicable for all Kenwood radios that do not have DVD or DVD screens located on unit.


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds

(so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio

stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key on the remote
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key on the remote

The security is canceled and the set enters the TUNER mode!

The above was pulled from:
http://forum.ecoustics.com/bbs/messages/4/134366.html

Hope this helps

Jul 04, 2008 | Kenwood Car Speakers & Subwoofers

2 Answers

When i hook up my ipod to my kenwood kdc mp728 i cant figure out how to play it through the radio


it should be in aux try to press source buton and see if that is an option if not an alternative is to hook it up on the back of the cd player in the audio in or aux or aux 2 using a wire adapter from walmart in the car sterio section

Sep 14, 2008 | Kenwood Car Speakers & Subwoofers

1 Answer

Factory code for Kenwood car stereo


5227

KENWOOD SECURITY CODE CLEAR procedure

These codes are applicable for all Kenwood radios that do not have DVD or DVD screens located on unit.


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds

(so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio

stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key on the remote
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key on the remote

The security is canceled and the set enters the TUNER mode!

The above was pulled from:
http://forum.ecoustics.com/bbs/messages/4/134366.html

Hope this helps

Jul 04, 2008 | Kenwood Car Speakers & Subwoofers

1 Answer

Hi I have just bought a seconhand car with a KDC 5016 how can i get the code reset, regards tony


If you have the remote you can clear it yourself with this method or if you do not have the remote you need to take it to an authorized Kenwood repair center and they can do it for a small fee. But you must have the remote.
This method below is right out of the service manual for your model.
I would appreciate a good rating if this helps you. Thanks and let me know if you need any further help with it.

How to clear the simple security code (K type only)
1. While the code is requested, press and hold the DISP
key and press and hold the VOL Up key for 3 seconds.
("........."disappears.)
2. Enter “KCAR” from the remote control unit. (Same
operation as the '98 model)
• Press numeric key 5 twice then press the Track Up
key. (This enters "K".)
• Press numeric key 2 three times then press the Track
Up key. (This enters "A".)
• Press numeric key 2 once then press the Track Up
key. (This enters "A".)
• Press numeric key 7 twice then press the Track Up
key. (This enters "A".)
3. The security is canceled and the unit enters the
TUNER mode.

Jun 20, 2008 | Kenwood Car Speakers & Subwoofers

1 Answer

Require unlock code for unit as no documentation, this unit arrived in a vehicle i bought from japan and i m eager to get it to work. HDV-910 Kenwood


As I have informed another person on this site; there are only two ways to aquire an unlock code, you'll have to send it back to Kenwood or ask the person who sold you the car. If you send it back to Kenwood they'll require proof of purchase.

Jun 14, 2008 | Car Speakers & Subwoofers

Not finding what you are looking for?
Car Speakers & Subwoofers Logo

Related Topics:

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Speakers & Subwoofers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Larry Spears
Larry Spears

Level 3 Expert

625 Answers

Are you a Kenwood Car Speaker and Subwoofer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...