Question about Washing Machines

1 Answer

MAYTAG WASHER MAH7550AAW

I CANT FIND ANYWHERE THAT SELLS THE LCD MEMBRANE FOR THIS WASHER

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Washing Mach... Master
  • 2,651 Answers

Heres a sight that might be helpful

http://www.searspartsdirect.com/partsdirect/index.action

Posted on Oct 19, 2008

Testimonial: "great help thanks!!! "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install the shipping bolt for maytag lat2500 washer?


Hello Phyllis,

The way Maytag did that was by a plastic ring that fit in the lid rim it was deep enough that it would fit inside the top rim of the outer tub cover locking the tub into place. If in your area their is a small independent shop that sells and services Maytag appliances they may have a extra one lying around in the back,if not a peice of styrofoam shaped to fit under the lid and into the tub it would lock the tub into place for shipment.

Gene

Aug 01, 2011 | Maytag LAT2600A Top Load Washer

Tip

Maytag Neptune Front Load Washers No Spin Problem


A class suit was filed in the State of Illinois, USA and then later on won against Maytag in 2004 due to the high failure rate of the wax motor used in the door lock mechanism of their Neptune Front Load Washers. The wax motor is used to activate the door lock switch by extending its shaft when a voltage from the machine control is applied across its terminals. Its failure then leads to the breaking down of components in the expensive machine control board. This is the fact that angered the customers which led to the filing of the class suit.

The obvious symptom of a failed wax motor is the inability of the washer to advance to the spin cycle and the door lock lamp is not turned on. The washer stops momentarily at the end of the wash cycle then continue to tumble as the machine control checks the activation of the door lock switch. The control will not allow a spin speed higher than 51 revolutions per minute (RPM) unless the door lock switch is activated by the wax motor. It is a safety feature of the washer to prevent accident due to accidental opening of the washer door during a high speed spin.

Customers who purchased the Neptune Front Load Washers in the USA after April 1, 1997 and before August 9, 2004 are Class members and eligible for the repair reimbursement, replacement cost, or purchase certificate depending on the length of service of the machine. Call up Maytag at 1-888-MAYTAG (1-888-629824) for more information.

The models included in the class suit are as follows: MLE2000AYW, MLE2000AWW, MLE2000AZW, MLG2000AWW (Gas Stack Unit), MAH3000AAW, MAH3000AEW, MAH3000AGW, MAH3000AWA, MAH3000AWW, MAH3000BGW, MAH4000AWW, MAH4000BWW, MAH4000AWQ, MAH4000BWQ, MAH5500AWW, MAH5500BWW, MAH5500BWW, MAH5500BWQ, MAH55FLBWW, MAH55FLBWQ, MAH6500AWW, MAH6500AWQ, MAH7500AWW, MAH7500AWQ, MAH7550AAW, MAH7550AGW.

on May 06, 2010 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Matag washer travels across the floor.


Velcro is a silly idea, what you want it to rest the washer on a rubber membrane as this will absorb all vibrations and kinetic energy thus stopping it from moving.

http://www.gkacoustics.com/anti_vibration_rubber_mats.htm this place sells them (aswell as other places) Neoprene Rubber and MLC Closed Cell Rubber is your best bet.

Hope this helps

Jan 03, 2010 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag neptune washer keeps beeping


The Service Manual for reference. Sears Parts Direct for reference.
I have tried to work with a few folks on this issue never received feed back to resolution see this post. I feel the issue is caused by one of three possible issues.

A stuck key issue/defective Spin Cycle key making constant contact forcing the Key/LED to cycle thru the Spin Cycle settings. Under normal conditions if you press and hold the Spin Select key it will cycle thru the settings, yours has a mind of its own (defective issue).

A false signal from the Control Board for the Spin Cycle.

A corrosion path issue at the Membrane Pad ribbon cable socket connection between pins 5 and 4. See page 20 of the SM button functionality “Spin” key.

Try to verify that the spin cycle membrane key is not stuck/defective signaling the Control Board to cycle thru the spin settings. I have not experienced this issue but let’s try the Membrane Pad Test to get a start point. See the Service Manual page 15, I have modified the process to make it a bit more understandable at least for me. Make sure the two digit display is not On or Lite.
Press the off button first so there is nothing displayed in the Two Digit display of your FAV6800AW.

Now Enter / Exit Service Mode


To enter Service Mode press the Enviro Plus and Spin Only keys for three seconds or until the control beeps. While in Service Mode, pressing the Presoak key will start a membrane switch check that verifies switch operation.

All the LEDs (except Presoak ) can be toggled or slewed by pressing the key associated with the LED or set of LEDs. Do not press the Presoak again during this test.

Press each key once and only once including the Signal Key the on side and the off side, also the UP and Down Arrow key of the LED display. All keys (including the OFF button) must be pressed within 5 minutes for this test to pass. “PA” will be displayed for five (5) seconds once all keys have been pressed and the test is completed (more like PA will be displayed for only a few seconds on my FAV6800AW). Following 10 seconds of inactivity at any point, this test will exit without any display. Let us know the results.

See my additional comment this board has message limit issues.

Sep 17, 2009 | Maytag Neptune FAV6800AW Top Load Washer

3 Answers

Maytag Neptune Tl Spin settings



I would try verify that the spin cycle membrane key is not stuck/defective signaling the controller to cycle thru the spin settings. I have not experienced this issue but let’s try the Membrane Pad Test to get a start point.

Do you have the troubleshooting guide stored in the control panel? It was shipped with the machine, pull 120VAC washer power plug, remove the top three torx screws at he top back of the control panel and remove the trouble shooting guide. Rassemble and power up your machine. Follow the instructions for Membrane Pad Test. You will enter Service Mode to verify that the key pad function LED can be toggled, just press each key once except the Presoak key as described below. If you don’t have the Troubleshooting guide that came with your FAV6800A I have pasted in the test from the SM;

Enter / Exit Service Mode
To enter Service Mode press the Enviro Plus and Spin
Only keys for three seconds or until the control beeps.
Membrane Pad Test
While in Service Mode, pressing the Presoak key will
start a membrane switch check that verifies switch
operation. All the LEDs (except Presoak ) can be toggled
or slewed by pressing the key associated with the LED or
set of LEDs. Each time either set delay arrow is pressed
the digits toggle between a blank and 8. All keys
(including the OFF button) must be pressed within 5
minutes for this test to pass. “PA” will be displayed for
five (5) seconds once all keys have been pressed and the
test is completed. Following 10 seconds of inactivity at
any point, this test will exit without any display.

Let us know your results.

Dec 30, 2008 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Maytag MAH7550AAW problem


first check under or bottom back of the unit to see the drain hose from the tub , then disconnect the hose from the tub and pull the hair , lint ,ect... that you can
if that don't make it drain better the the front will have to come off , but also if the pump motor is getting weak it may need to be replaced

electech

Oct 26, 2008 | Washing Machines

1 Answer

I need an extention hose for the Washer Outlet Hose, on Maytag Model, mtw6700tq1, Bravos Model. thanks


Home Depot sells it. With a rubber end that slips over the end of the discharge hose that comes with the washer.

Jun 24, 2008 | Maytag Washing Machines

4 Answers

Neptune front load washer buttons wont work


I tried un pluging the machine for few hours and it will work for 3-4 load and then it will lock up again

Nov 20, 2007 | Maytag Neptune MAH5500B Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...