Question about Mitsubishi WD-52525 52" Rear Projection HDTV

1 Answer

Blinking Green Light on Mitsubishi DLP 52525

I have had a Mitsubishi DLP 52525 for 2+ years now and recently the green timer light started to rapidly blink when the unit was turned on and it continued to blink without the picture coming on. After discconnecting the power and then using the system reset button, the problem remained. I swapped out the lamp and the tv worked for about a day and now the same problem is occurring. I have hit the system reset button but to no avail. There is nothing in the manual that deals with what is indicated by a constant blinking green timer led. Looking for suggestions. I have a Mitsubishi WD-52525 that has the green blinking light problem as well. I have replaced the bulb, but I don not get a picture when I turn on the TV, just sound. Now when I hit the reset button, it blinks green, then clicks off with a solid red light. When this TV was working properly I would notice a faint siren like sound when the TV was first turned on and before the picture would appear, but now I don't seem to be hearing that sound anymore. Any ideas on how to get this TV working again?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 899 Answers

The circut that detects the bulb has been also failing in these sets
and the conversion chip that controls the picture , and the transformers are not putting out the full power they are supposed to.
this set will need to be tested to determine the exact cause or causes

Posted on Oct 18, 2008

  • jason Oct 19, 2008

    that siren sound is the CRT and FLYBACK transformer along with other chips that are acting up so the frequency sound that is created when this occurs is that sound that you are hearing ,( usually you don't hear much of anything because evrything is running smooth)

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The DVD player on my Bush 32inch television takes in DVD's but just displays 'No Disc' the model number is DLED32165HDDVD Is it something I can fix?


The player has failed, these types of devices are not fixed as the cost to repair is in some cases more than a new one. More than likely you could not get parts for it even if you knew the cause, which is most likely a failed laser light

Jan 06, 2017 | Bush Televison & Video

1 Answer

I recently bought a telefunken tdv-322 dvd player with usb, but when i put a usb in, it does it doen not even pick up the usb itself... extremely frustrated right now.


What usb are you using and is it activated on the machine?
ELECTREPAIRUSA@ELECTREPAIRUSA or you can contact us at that address as we repair/renovate all items electronic and electrical old and new.

Jan 02, 2017 | Televison & Video

1 Answer

When playing commercial DVD's, my DR-MV150B starts to stall. It stops with the picture on the televsion screen, but can't see the rest of the movie. Any thoughts? The disc does eject.


Try cleaning the laser with a bud, if not it's either the spindle motor or laser assembly,
ELECTREPAIRUSA@ELECTREPAIRUSA or you can contact us at that address as we repair/renovate all items electronic and electrical old and new.

Jan 02, 2017 | JVC DR-MV150B DVD Recorder/VCR

1 Answer

Can't switch off tv


All tvs draw a current so long as they're plugged in, this is what allows a remote device to power them on. Modern tvs will generally have a light to designate this (I think this is what you're referring to as standby). The only way to cut the current to your tv would be to unplug it or if it's connected to a surge protector, switch that off.

Jun 28, 2014 | Televison & Video

1 Answer

Do a 2001 GE projection tv have a lamp in it?


Yes course there is a lamp . You can order one from ebay for around $10 .

Apr 21, 2014 | Televison & Video

2 Answers

Blu Ray - DVD player does not respond to remote


Did you check to see if remote pickup on player is cleal and not being blocked?

Dec 15, 2013 | Televison & Video

1 Answer

Would like to know the codes for a LG tv, Sony tv, and a TOSHIBA DVD ?


How to Program


Remotes With SET Button
1. Choose and press a device key i.e TV. LED will flash once.
2. Press "SET" Hold until the LED Lights up.
3. Enter the 4-digit Device code (refer code list).
4. The LED will flash once as each number is programmed at the end of the 4 digit the LED will turn off immediately if correct. If the LED flashes then something went wrong in the process. If the first code does not work then repeat the process with the next.
5. Important - Some brands use other manufacturers to make their devices if the codes available do not work the try the MAGIC search function.


Remotes Without SET Button
1. Choose and press a device key i.e TV. LED will flash once.
2. Press and hold BOTH the CHANNEL UP AND VOLUME DOWN button until the LED Lights up.
3. Enter the 4-digit Device code (refer code list).
4. The LED will flash once as each number is programmed, at the end of the 4th digit the LED will turn off immediately if correct. If the LED flashes then something went wrong in the process. If the first code does not work then repeat the process with the next.
5. Important - Some brands use other manufacturers to make their devices if the codes available do not work the try the MAGIC search function.


MAGIC SEARCH FUNCTION
1. The magic search function enables you to scroll through the entire code list one by one by pushing the on/off button. Each time you push the on/off button the remote automatically switches to the next code in the list and sends a signal to the device you have chosen.
2. Choose and press a device key i.e TV. LED will flash once.
3. Press and hold the SET button or if no SET button then hold BOTH the CHANNEL UP AND VOLUME DOWN button until the LED Lights up.
4. Enter the 4-digit Device code (refer MAGIC list) i.e TV is 0001.
5. The LED will flash once as each number is programmed at the end of the 4 digit the LED will turn off immediately if correct. If the LED flashes then something went wrong in the process.
6. Start scrolling by pushing the ON/OFF button as soon as your TV or Chosen device turns OFF lock the code in by pushing the DEVICE key again.

Mar 27, 2013 | Televison & Video

2 Answers

Akai PDP4206EA lost tuner and video inputs


Mine died after a brown out. It turned out to be the main board. They're pretty hard to find.

JE

Aug 14, 2009 | Akai PDP4206EA Television

Not finding what you are looking for?
Mitsubishi WD-52525 52" Rear Projection HDTV Logo

547 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1207 Answers

The Knight
The Knight

Level 3 Expert

71754 Answers

Jaime Hernandez

Level 3 Expert

2294 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...