Question about Vtech 5.8 Ghz Handset Cordless Phone System with Digital Answering & Caller ID

3 Answers

Phone are 5.8 ghz vtech

5.8 ghz set of 4 .This only happens on phones 2 3 &4 not on main phone
Phones are vtech 5.8 ghz
Phone beeps a couple of times then cuts out .They are also very noisy and I have to hold them a certain way to cut noise down

Posted by on

  • gerryandbev Oct 19, 2008

    WHAT ABOUT THE PROBLEM OF PHONES 2 3 & 4 BEEPING AFTER 45 SECS AND THEN THEY CUT RIGHT OUT AND I LOOSE THE CALLER . THIS IS VERY ANOUYING.THESE PHONES DID THIS FROM DAY ONE.

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,614 Answers

You must register all connected phone to the base phone, follow this few steps:

To use VTEXH 5.8 into other phone;

1. After charging the battery, the screen will display:

2. Press SEL, you will see ENTER BASE ID, if the
screen already says ENTER BASE ID, go to step 3.

3. Enter the 15 digit base unit ID code, located on the
underside of your mi 6820. If you make a mistake,
press the DELETE key to backspace (delete characters),
then enter the correct information.

4. Press SEL to complete the registration process.

5. Once a valid base ID code has been entered, the
display will blank for a second or two, and then
show:

6. If the base accepts the new handset, after several
seconds the new handset will show:
where X is the new handset number assigned,sequentially,
by the base.

NOTE: The 15-digit BASE ID Code may contain numbers and characters,
including0 through 9 and *. Make sure you enter all 15 digits.


===

De-register all system handsets by:
1. Unplug the base power plug.
2. Press and hold the PAGE key.
3. Plug the base unit power plug back in and con
tinue to hold down the PAGE key for 10 seconds.
4. This will erase all handsets registered to the
base. The handsets will now prompt you to:
5. Enter the 15 digit base unit ID code, located on the
underside of your mi 6820. If you make a mistake,
press the DELETE key to backspace (delete characters),
then enter the correct information.
6. Press SEL to complete the registration process.
7. Once a valid base ID code has been entered, the
display will blank for a second or two, and then
show:
8. If the base accepts the new handset, after several
seconds the new handset will show:
where X is the new handset number assigned,sequentially,
by the base.

Follow this few steps, this was intend to register again your handset into your base.

Posted on Oct 19, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 538 Answers

Well..sounds like interference on the channel. do you have anything else on that same frequency that you can trace down. turn on a phone, and walk around your location, and listen for a higher hum or static. That may be what is at issue here.

Posted on Oct 19, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 136 Answers

May be the frequency problem for noise problem.
pleaSE CHECK IT OUT.
ADJUST THEM AT SOME PROPER LEVEL..
AND THEN TRY.

Posted on Oct 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a Vtech 5.8 GHz Digital Answering Machine with 4 handsets sModel MI 6896 and have lost the manual. Can I download a replacement? I also have two batteries that need replacement I think. The...


You can download the manual at
http://vt.vtp-media.com/ecp/documents/product_Product/791/UserManual/2095/mi6896_manual.pdf

One source for batteries is
http://www.batteriesplus.com/products/549-0/5325-Cordless-Phone-Batteries/127618-Vtech/mi6896/1.aspx

Dec 04, 2010 | Vtech 5.8 Ghz Handset Cordless Phone...

1 Answer

I have a three handset 6.0 v tech. the one handset keeps beeping. What is going on?


With vtech phone (many times) a beeping handset indicates a low battery or an inability to connect to base station. check to make sure the battery is connected correctly and that the phone is setting in its docking station correctly. (remover and obstructions that would prevent correct charging) If this fails go to your local store that sells batteries for cordless phones and purchase to correct type.

Oct 13, 2010 | Vtech 5.8 Ghz Handset Cordless Phone...

1 Answer

Vtech;5.8 ghz'#cs5121-2: how do i silence the phone to turn off ringer and then turn it back on>


go to main menu select the option of ringing or tone set-up and then select ringer type select silent same procedure done turn back or u can also fallow guideline book

Nov 01, 2009 | Vtech IA5854 5.8 GHz Cordless Phone

1 Answer

Phones stopped working. They only read


first step is to unplug all power and phone connections from the wall for all Vtech phones and bases.

Second,plug each set and base in the wall for power one at a time.

Go back to the basics and pair the handset with the base of the unit.

Do this for all sets one at a time.

May 29, 2009 | Vtech 5.8GHz Cordless Phone with Digital...

1 Answer

Phone wont connect to verizon. message on phe says place set in


Unplug main unit and the other unit which is not working then plug back on after few minutes. If its still the same then change battery on hand set. baattery life is only four years

Mar 26, 2009 | Vtech 5.8 Ghz Handset Cordless Phone...

1 Answer

Cannot reregister phones to the base.


If your base is a VT2651:
1) take phone off of the base's cradle.
2) enter **335782 on the keypad
3) phone beeps
4) remove all batteries from handsets.
5) reinstall battery in 1st handset, and enter the code number for the base unit (sticker on bottom of base). First handset will be set to phone 1
6) repeat step 5 for all other handsets.

If your base is a VT2656, there is no keypad on the base. I don't know the trick to reregister the handsets. I wish I did, since that is the problem I am having.

Nov 22, 2008 | Vtech VT2600 Additional Handsetfor...

3 Answers

User manual


need copy of manual for vtech 5.8ghz cordless phone with 2
additional handsets in english.

Nov 17, 2008 | Vtech IA5854 5.8 GHz Cordless Phone

1 Answer

Working one set of Vtech 6041 cordless phone set with another?


I have the vtech dect6.0 with one answering system and two remote docking systems.I can phone out from the remotes but cannot receive incoming calls from the remote.When I pick up the remote to receive the phone immediately shuts off.

Aug 19, 2008 | Vtech Cordless 6041 Phone

1 Answer

Low battery


You need to buy new batteries for your phones. Large retailers charge $10-12 per battery but you can usually find them for closer to $4 online at amazon.com or eBay.

Jun 22, 2008 | Vtech 9009111 Cordless Phone

Not finding what you are looking for?
Vtech 5.8 Ghz Handset Cordless Phone System with Digital Answering & Caller ID Logo

568 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vtech Phones Experts

kakima

Level 3 Expert

96518 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Cindy Wells

Level 3 Expert

4757 Answers

Are you a Vtech Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...