Question about Arris DSR922

2 Answers

Motorola dsr922 lockup on startup

I didn't know not to unplug the 922 during mem. battery replacement. I wrote down the receiver id numbers but I need a repair station near North Florida to revive the receiver if possible. Thanks ... steve...stmorg@alltel.net

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

ATS electronics can repair the board that died. running out of boards is not a problem. the dsr-920 receiver is junk if the battery dies..the chip that stores the unit ID number is no longer manufactured....

Posted on Aug 08, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

If you have lost your receiver ID number you will need a new main board.
Check the receiver number in the status screen. If it matches the UA number on the back sticker you are ok, if not the only solution is replacing the main board. ATSelectronics.com still had some boards when I last checked. But when they run out were all screwed.
Motorola didn't make any provisions for renewing the ID number.
That really sucks motorola ;-(

Posted on Jan 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is a good place to have the motorola 922 receiver repaired.


ATS Electronics. they are motorola's authorized service center

Jul 20, 2009 | Arris DSR922

2 Answers

DSR 922- to begin with it wouldn't shut off, no function will work with the remote, unplugged it and replugged it and now there is nothing but the inspirational channel on G3 217. H20


IF the receiver lost its sat settings you had, you best check the internal battery. the lithium battery should be 3.70 volts...if its dead you need to replace it, without interupting the power source...this will also cause you to lose your unit ID number. then you won't be able to subcribe to programming...the 922 can be repaired if the battery dies.

Jul 09, 2009 | Arris DSR922

1 Answer

How to load w5 satellite manually in my 4d-922 receiver


Lost W5 & X4 on myDSR922 how can i get them back?

Apr 08, 2009 | Arris DSR922

1 Answer

I get get digital signals on dsr 922


does the creen say searching for channel? if so you might have to update the maps...go to G! 3 and leave there for about 15 to 20 minutes...make sure you got a dc light....if no you have a tuning issue...play with the skew...

Feb 16, 2009 | Arris DSR922

1 Answer

How do I decipher the SN on a Motorola DSR922 receiver.


The DSR922 was made from 2001-2007. No more being made from motorola ;-(
The seventh digit from the left is the date code.
So a 4 in that place means manufacture date of 2004.

Jan 29, 2009 | Arris DSR922

1 Answer

My dsr922 will not boot up properly


clear the receiver to factory setting and start over.

Jan 15, 2009 | Arris DSR922

1 Answer

Dsr 922 no dc light on g1 etcs


you are not on the satellite. need to reporogram or fine tune these satellite into receiver.

Oct 11, 2008 | Arris DSR922

2 Answers

Power outages cause receiver to lose unit ID numbers.


When the backup battery goes dead you loose the ID number.
http://www.pacificsites.com/~alanjudd/922.htm
If you have lost your receiver ID number you will need a new main board.
Check the receiver number in the status screen. If it matches the UA number on the back sticker you are ok, if not the only solution is replacing the main board. ATSelectronics.com still had some boards when I last checked. But when they run out were all screwed.
Motorola didn't make any provisions for renewing the ID number.
That really sucks motorola ;-(

Sep 05, 2008 | Arris DSR922

2 Answers

I cannot get in any digital signals today.


Same thing happened to me. After much research I found out that the digital descrambler was dead. I found a good used unit on e-bay, but I found out later that the repair usually averages about $120. I plan on getting the old one repaired for a spare. Contact ATS Electronics at 828-465-9968. They have a set labor rate of $98 plus parts.

Aug 12, 2008 | Arris DSR922

Not finding what you are looking for?
TV Receivers & DVRs Logo

Related Topics:

544 people viewed this question

Ask a Question

Usually answered in minutes!

Top Arris TV Receivers & DVRs Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

68202 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Are you an Arris TV Receiver and DVR Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...