Question about ASUS P5P800S Motherboard

1 Answer

The power led and reset led was both on

Am done follow your instruction sir nothing happen its they same, by the way sir thanks you for your time and helping me,what you think sir maybe the motherboard had a problem?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 189 Answers

Yes, *********** board has a problem. It has a short circuit. between the power led and reset.

Posted on Oct 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Says to reset color ink tank. put a new one in and says same. reset many times nothing happens


Following step by step resetting canon Pixma iP90 :
  • Before resetting printer canon iP90, start with printer power off .
  • Press resume button coincide with power button.
  • While pressing power button, release resume button.
  • Press resume button 2 times and then release both button
  • Green LED indocator will blinking and then stopped blinking.
  • When the Power LED lights in green, press resume button 4 times.
  • Press power button and the printer power will off. otherwise off, depress again power button.
  • And the turn on the printer again, your printer canon iP90 should be response as normal.

Feb 21, 2011 | Canon PIXMA iP90 Mobile Printer

1 Answer

Red diag light flashing


This is happening because the firmware did not load correctly.

Please follow the link below and follow the instructions. there are many steps to use to resolve this.

Hope this helps!
Jim

http://www6.nohold.net/Cisco2/ukp.aspx?pid=10&login=1&app=search&vw=1&articleid=4861&donelr=1

May 30, 2010 | Linksys EtherFast Cable/DSL Router

2 Answers

I have purchased a ''Virtually Mint'' Canon Pixma ip90 printer however, when I try to print a document a message pops up stating ''the following ink tank is not installed: black ink tank, colour ink tank....


Hi there you can try.
Following step by step resetting canon Pixma iP90 :
  • Before resetting printer canon iP90, start with printer power off.
  • Press resume button coincide with power button.
  • While pressing power button, release resume button.
  • Press resume button 2 times and then release both button
  • Green LED indicator will blinking and then stopped blinking.
  • When the Power LED lights in green, press resume button 4 times.
  • Press power button and the printer power will off. Otherwise off, depress again power button.
  • And the turn on the printer again, your printer canon iP90 should be response as normal.
All I ask is please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Jan 21, 2010 | Canon PIXMA iP90 Mobile Printer

3 Answers

When I push button to turn on, the light flashes orange. Nothing happens, no fan, nothing. It worked fine yesterday.


This usually means a failed power supply and/or failed system board. No way to know further without swapping parts. Power supply is cheaper to replace .

Oct 05, 2009 | Dell Dimension E510 Dual Core 2.8 Ghz...

1 Answer

Newly installed car alarm, LED in solid light n horn/siren blares


if you follow instruction properly than the alarm should work properly, Go over your wiring again 2-3 times make sure it make sense to you with the instructions. If it make sense than take the unit back and get another, can be faulty alarm.

Aug 26, 2009 | 2003 Toyota Corolla

1 Answer

Dead sharp pc-ax40


You can try reseating the memory and the hard drive if you can get to it, but it sure sounds as though the motherboard is shot.
You can take it to your local computer repair shop.
Good Luck.

Mar 15, 2009 | Sharp Computers & Internet

2 Answers

Can't bring up Setup Wizard


yeah the same problem. not able to launch the wizard from the URL.

Actually i was trying to change the password for the wireless secure access and i tried typing different combinations and got in problem, then thought of doing a reset and start again the whole configuration, so i did used the reset hole and followed the instructions as listed in the document (ie like doing the configuration for first time). after restarting computer and access the http://192.168.0.1 URL, nothing happens, i'm not able to get the setup wizard. I also noticed that the LEDs are displaying properly as mentioned in the manual... now.. how to get it setup wizard....

plz help

Apr 15, 2008 | D-Link DI 514 Wireless Router (DI-514)

3 Answers

Canon ip pixma 1500


hi dear
try this methode

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting formenu selection)
4) When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED
lights alternately in
orange and green, starting with orange.)
The number of the Reset
button pressing
LED Function Remarks

0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection


that's all

Mar 27, 2008 | Canon PIXMA MP160 All-In-One InkJet...

Not finding what you are looking for?
ASUS P5P800S Motherboard Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top ASUS Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18381 Answers

David
David

Level 3 Expert

778 Answers

Are you an ASUS Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...