Question about LRD6399SWS Radar Detector

1 Answer

LRD6399SWS What is the difference between the green light and red light?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 64 Answers

LED Display gives you your display visual alerts, signal strength, and operation mode. Here is an attached link for the manual.....http://www.uniden.com/pdf/LRD6399SWSom.pdf
But to answer your question here is what the difference between the green light and the red light are:
1. X-Band Signal Indicator—A green LED lights and blinks to
indicate the presence of an X-band radar signal. The blink rate
increases as the radar source gets closer. A distinct audio alert is
also heard.
2. K-Band Indicator— An amber (orange) LED lights and blinks to
indicate the presence of a K-band radar. The blink rate increases as
the radar source gets closer. A distinct audio alert is also heard.
3. Ka-SuperWideband Signal Indicator— A yellow LED lights and
blinks to indicate the presence of a Ka-SuperWideband radar
signal. The blink rate increases as the radar source gets closer. A
distinct audio alert is also heard.
4. Laser Signal Indicator— A red LED under L lights and blinks to
indicate the presence of a laser signal. A distinct audio alert is also
heard.
5. SWS Signal Indicator— When an early warning hazard or
informational signal is detected, the yellow SWS LED begins to
blink and the amber K-band LED lights. A distinct audio alert is
also heard.
6. Power-On Indicator— A green LED under P lights to indicate
power is being supplied to the unit and the unit is turned on.
7. LED Signal Strength Meter—Four LEDs give an accurate visual
indication of the strength of radar or laser signals.
8. City Mode Indicator—A green LED under C lights to indicate
that you selected City Mode.
9. Auto Mute Indicator— A red LED under M lights to indicate that
you selected the Auto Mute feature.

Please make sure you give me a rating and I hope this helps,
cbinny1



Posted on Oct 20, 2008

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What wire to solder on the ciggy plug?


Red is your positive black is ground yellow constant power green is a wire that does not need to b used nor the yellow unless u want constant power to the unit positive red wire goes to the front of your ciggy adapter black can go on edit hie side of the two grounds that hold your ciggy adapter inside the socket hope this sheds some light on it

Mar 03, 2014 | Passport 8500 X50 Radar Detector

1 Answer

I have a green light and orange light on my dash indicating which mode its in (city/highwsay). which is which?


Just remember that "green means go" as in, you are on the highway at a higher rate of speed and need maximum range from your system.

Amber is the "city" mode and reduces the sensitivity of the unit for when you are in the city or congested traffic.

Aug 14, 2011 | 1000P Radar Detector

3 Answers

I lost my cord and would like to make a basic power cord can u send me a diagram that shows the color code on the end that looks like phone wire i have material but i dont know where which wire goes...


on a 4 wired RJ11 or Rj12 Phone plug, it's the middle 2 wires. green and red are your positive and neg. Do a quick touch test to confirm which is pos and neg. only works one way. after confirmed. solder the wires and wrap insulation tape around each and then a couple times over both for strength. the phone wire is prone to breakage.

Apr 23, 2011 | Vector 995 Radar Detector

1 Answer

Uniden LRD6399SWS Radar Detector: I need a user manual


Download and print from http://www.uniden.com/pdf/LRD6399SWSom.pdf

Dec 31, 2009 | LRD6399SWS Radar Detector

1 Answer

Smart cord just flashes


Try the following. First, make sure if possible that the 9500i is powered off when you plug it into power. Then hold down the buttons (I forget which ones) needed to put it into USB mode and only release these buttons once "USB" is displayed after plugging it in again. Hopefully you will be able to get your 9500i to display "USB" again. If you can get it to display "USB", only then plug in its USB cable into your computer. Then run Detector Tools and see if you can re-flash the firmware.

Jun 24, 2009 | Passport 9500i Radar/Laser Detector

1 Answer

Uniden radar detector


Go to uniden.com they should have it to download incustomer service

Nov 29, 2007 | LRD6399SWS Radar Detector

1 Answer

Jammer shuts off


To my understanding,the first 30 seconds is a test mode when the blinder will react to a tv remote,after wards the light will remain green until a true laser attack.

May 27, 2007 | M20 X-Treme Radar Detector

Not finding what you are looking for?
LRD6399SWS Radar Detector Logo

750 people viewed this question

Ask a Question

Usually answered in minutes!

Top Uniden Vehicle Parts & Accessories Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13215 Answers

Brad Brown

Level 3 Expert

13751 Answers

Are you an Uniden Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...