Question about HP 1024 LE (White) 14 in.CRT Conventional Monitor

1 Answer

Horizontal problem Sir I went to service a HP 1024 monitor. the problem is the horizontal adjustment switch is not working even i changed the front switch. Rest of all controls are functioning properly.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 513 Answers
Re: horizontal problem

CRT monitors are basicaly the same as TVs which are along with micros and rabid rotweilers the most dangerous thing in a house to service. They can store very high voltages even after plugged out, enough to kill. Take care and don't go any further unless you are aware of all the safety issues. If you want more information on the required equipment and SAFETY PRECAUTIONS, go here: Probably, your GS monitor uses little 3-position 'tab switches' which can be reached from the rear of the main circuit board. One of the switches should set vertical position. You will need to remove the case. You will need to unplug the cable going to the side-mounted controls and, then, once the case is off, remove the side-mounted controls from the case and reconnect to the circuit board to do the adjustments. This is kind of a hassle; so, while the case is off, you may want to check the Focus and Intensity settings (slotted shafts on the black HV module). Also, this is a good chance to dunk your case in a sink of soapy water. NOTE --> Be sure to wear goggles/ work on a non-conductive table surface/ have a fat magazine ready to support the circuit board/ avoid stressing the CRT neck/ stay away from the HV anode lead (plugged into the back of the CRT) and avoid touching the back of the CRT. Good luck

Posted on Jun 11, 2006

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Hp monitor 2031s does not scan signal from gateway gt5432...

Go back to Dell monitor. Remove any video drivers from hp.change video resolution both in windows and in video card settings to standard 1024 x 768 (yes it will look horrible) then hook up hp monitor. Don't install drivers if prompted get them from hp website then adjust resolution through video card settings after drivers installed which probably require restart.

Dec 01, 2013 | HP Computer Monitors

2 Answers

The issue is that I had an XP machine and I bought a brand new HP deskktop Windows 7 and as soon as I turned it on I got a message on my Kogi that I should change the settings to 1280 X1024. Since I did...

To change the screen resolution, click on Start - Control Panel - Display - Settings tab and the adjust the screen resolution slider to 1280X1024 click Apply.

Feb 03, 2011 | Kogi l7eh-ta ko 17" Flat Panel LCD Monitor

1 Answer

Good Evening Sir/Madam,I have a problem on my LCD Monitor,if i open my cpu it appears on the screen of my monitor is"Out Of Range"....what kind of problem is this sir,can you give me...

You have set too high resolution for your monitor. Follow these steps to correct the problem.

1. Switch on the computer.

2. Before you see the Windows logo, press F8 button several times. You will get the boot menu.

3. Select the option 'Enable VGA mode' with arrow keys. Press enter.

4. Computer will boot normally, but with larger icons.

5. Open Control Panel --> Appearance and Themes --> Change the screen resolution.

6. Set the screen resolution to 1024 x 768 (or something close to it).

7. Apply the settings and restart the computer.

This will solve your problem. Wish you Good luck!

Nov 12, 2010 | ViewSonic VA912 19" Flat Panel LCD Monitor

1 Answer

Every time i try to go on my webcam it tells me that the hp media smart webcam does not support a screen resolution smaller then 1024 by 768?

I've had problems using a widescreen monitor with certain programs/devices when my horizontal resolution is set high enough (for example: 1024), but my vertical resolution is too low (for example: 700). This may be your problem check the display settings and increase if necessary.

Hope this helps you.


Steve G.

Nov 02, 2010 | HP w2558hc 25.5" Widescreen LCD Monitor

1 Answer

Resolution problem

This monitor's standard resolution is 1280x1024. I would update your graphics driver. Just go into System Properties, and open up the Device Manager. (Press WinKey+Pause/Break key to open System Properties, and Device Manager is in the Hardware tab.) Locate the graphics driver in the Device list, right click and update the driver.

Feb 26, 2010 | LG Studioworks 700S 17" CRT Monitor

1 Answer

I just purchased an HP w2007 hp monitor. After going through all the suggested start up routines, images are stretched horizontally. I'm using XP home edition with sp 3. My resolution doesn't seem to go...

if it's a wide screen monitor then the monitor is likely doing the stretching and you have to adjust using the monitor controls (either buttons on the monitor itself or it may have come with software as well if you loaded a CD when you first installed).

Mar 31, 2009 | HP W2007 LCD Monitor

1 Answer

Less H-width for higher resolutions

this is not the electronic problem, this monitor is made to support such (800x600) resolution.

Dec 17, 2008 | Compaq 7500 17" CRT Monitor

1 Answer

Usercontrol automatically displayed when bootup

Please change the switch pannel  and check 

Nov 19, 2007 | HP Compaq FS 7550 17" CRT Monitor

1 Answer

Kogi L9ch 19 in flat monitor

(I posted the latest post.) Change the resolution. (Mine was 1024 by 768, so I changed it first to 800 by 600 and then back to 1024 by 768, and it's back to normal!)

Hope that helps.

Feb 13, 2007 | Kogi L9CH 19" Flat Panel LCD Monitor

1 Answer

Monitor settings

Try to see if the resolution in your Operating System is not to small, Most likely the smallest for that monitor is 1280 by 1024, and see if the color quality is at 32 bit

Aug 22, 2006 | E-Machines eView 17f 17" CRT Monitor

Not finding what you are looking for?
HP 1024 LE (White) 14 in.CRT Conventional Monitor Logo

Related Topics:

512 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Computer Monitors Experts

Ivan Bernal

Level 1 Expert

8 Answers

Tony Isted

Level 1 Expert

49 Answers

Elizabeth Mescall

Level 1 Expert

7 Answers

Are you a HP Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides