Question about Hotpoint Aquarius WF210 Front Load Washer

2 Answers

Prewash always flashing

Can anybody help me the prewash light keeps on flashing all the time ?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: prewash always flashing

Yes i had a similar problem the prewash light kept coming on mid wash cycle and eventually stopped taking in the water just bypassing it straight to outlet without filling machine. i found if you remove the pump at the rear of machine and disconnect hoses there was a build of lets say deposits leading to a sensor through a opaque plastic connector to the top of machine . after cleaning the hoses thoroughly and removing all the crud machine worked as it should do, hope this helps

Posted on Jan 25, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 66 Answers
Re: prewash always flashing

Poss cold water is turned off or valve has gone

Posted on Jul 06, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Indesit WIA121 Flashing Door Lock, Prewash and Spin Lights - Machine not draining

hi something similar has started happening to our washer, after the initial wash starts the machine doesn't do anything for a while then the red door light flashes on and off very quickly as does the 1st and 3rd green wash cycle light?

Jul 04, 2012 | Washing Machines

1 Answer


If your PreWash is flashing then you have a pressure problem. You can dry using a washer machine cleaner or doing a hot cycle with white vinegar. If that doesn't help the electronic would have to be changed.

Jan 08, 2012 | Miele W412 Front Load Washer

1 Answer

HE3 doesn't respond to any button. Time light keeps flashing time. Pause cancel button does nothing, Cycle doesn't start. The only thing that will change is if you push a different mode ie, heavy,...

Unplug the machine for at least half an hour to eliminate the possibility of an electronic glitch. Then upon plugging in back, close the door then push CONTROL/ON (if present on this model). Select the DRAIN/SPIN cycle then select NO SPIN by pressing the SPIN SPEED button. Push PREWASH OPTION four times within five seconds. If PREWASH OPTION is not present on this model, press EXTRA RINSE four times within five seconds. C:00 will light up on the display. If the Starting procedure fails, push the PAUSE/CANCEL button then repeat the starting procedure.

In order to advance to the next step of the test procedure, push PREWASH OPTION button two times. If PREWASH OPTION is not present on this model, press EXTRA RINSE two times. The test program goes from C:00 to C:08 and should flash an error code when a problem is present. Post the code back for further troubleshooting, including the exact model number of the machine.

Sep 20, 2011 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

1 Answer

Why Prewash light is flashing?

I think you need to clean pump filter, if not at front, then remove lower rear panel of washer, locate and remove large black hose on drum ,remove and clean filter inside, remove hose onto pump and check for obstruction there as well.
Please rate my solution.

Nov 11, 2009 | Hotpoint WF430 Front Load Washer

2 Answers

The prewash light won't stop flashing and washer

get it checked by and expert it sounds like the board has gone or the door lock is faulty

Jun 28, 2009 | Washing Machines

1 Answer

When the washer go s on rinse the prewash flashes Problem

Mine has been doing the same ... each time it goes to the next part of the cycle the red light flashes but the machine doesn't do anything ... so up till I have been able to get the machine moving to the next stage by pressing the "Start" button ... unfortunately the machine will pause on each stage - meaning I have to press "Start" at each stage!

Dec 15, 2007 | Hotpoint Aquarius WMA52 Front Load Washer

3 Answers

Prewash flashing and machine Overfilling

Their is a small bowl connected by a see trough plastic pipe leading up to the preshour switch, that you will have to clean out the bowl and disconect the pipe from the presure switch and blow trough this to clean out any droplets of water. Replace then try the machine again, it may fill up again, dont dispair, empty the machine and re-blow trough the hose again with it disconected from the preshure switch. To empty the machine of water place the outlet hose into a bucket 3 or 4 times.


Oct 15, 2007 | Hotpoint Aquarius WF000 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WF210 Front Load Washer Logo

634 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts


Level 1 Expert

5 Answers


Level 1 Expert

47 Answers


Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides