Question about Pioneer DEH-1600 CD Player

1 Answer

Still geting feed back like a thump when volume is on 0 as i press the volume and when i scroll through the styles of sound

Is on 0 as i press the volume and when i scroll through the styles of sound

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

You have a bad ground. Or bad groun in the unit.

Posted on Oct 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Set clock on a jvc kd-r330


It's very simple even if you don't have the owners manual.
Step 1: Hold in the Menu button until "DEMO" shows on the display screen.
Step 2: Scroll with the volume knob until it says clock. Then press the volume knob to select it.
Step 3: Scroll with the volume knob until it says "CLOCK SET." Then press the volume knob again.
Step 4: Then adjust the hour first by scrolling with the volume knob. Once the correct hours shows press the volume knob and it will move on to the minutes.
Step 5: Once the hour and minute is chosen push the menu button again to finish the procedure.

Nov 13, 2013 | JVC Kdr330

1 Answer

How do I set the clock on my Pioneer DEH-P6200 cd receiver?


With the vehicle on, turn OFF the radio. Next, Press the Volume and hold the VOLUME knob. You should see LANGUAGE on the display. Scroll the VOLUME knob until you see CLOCK SET. Pres the VOLUME knob and the HOUR will start flashing. Scroll the VOLUME knob to set the hour then Press it to set the Minutes. When you're finished. Turn off the radio, then turn it back on. When the radio is in use, the Radio Station will scroll on the display, then the Artist information, then after a few seconds (20-30), the Clock will display.

Jan 14, 2011 | Pioneer DEH-P6200 CD Player

1 Answer

CMV1 is not working. When I press power button the


Check your grounds, you may have a bad ground connection behind the radio in the harness or your marine battery is having a ground issue, check that out first if that checks out ok then check out your speaker connections and make sure that they are wired ok. My experience with speaker thumps and pops has to do with ground.

Good luck.

Jun 19, 2010 | Clarion M255 AM/FM Marine CD Player

1 Answer

Alpine 9845 cde head unit car stereo i Cannot figure out how to access the Fader not the balance,altho i havent seen that function either. ive been to the alpine site and they dont even mention it. im sure...


Press the Rotary encoder (CDE-9845/CDE-9843
only) or press MODE (CDE-9841 only) repeatedly
to choose the desired mode.
Each press changes the modes as follows:
BASS → TREBLE → SUBWOOFER* → BALANCE → FADER
→ DEFEAT → VOLUME → BASS
BASS: -7 ~ +10
TREBLE: -7 ~ +7
Subwoofer : 0 ~ +15
Balance : L15 ~ R15
Fader : R15 ~ F15
Defeat : ON/OFF
Volume : 0 ~ 35

Feb 11, 2010 | Alpine CDE-9845 CD Player

1 Answer

Sony CDX-S2210 CD Player stuck on demo mode , cant adjust volume eq, skip track or anything


make sure the unit is switched off and the clock is displayed then

1 Press and hold (SEL).
The setup display appears.
2 Press (SEL) repeatedly until the
desired item appears.
3 Press the volume +/– button to select
the setting (example “ON” or “OFF”).
4 Press and hold
(SEL).
The setup is complete and the display returns
to normal play/reception mode.
Note
Displayed items will differ, depending on the source
and setting.
With the card remote commander
In step 3, to select the setting, press
< or ,.
The following items can be set (follow the page
reference for details):
“z” indicates the default settings.
*1 When the unit is turned off.
*2 When the audio output is set to “SUB.”
CLOCK-ADJ
(Clock Adjust)
(page 4)
BEEP To set “BEEP-ON” (z) or
“BEEP-OFF.”
SUB/REAR*1 To switch the audio output.
– “SUB” (z): to output to a
subwoofer.
– “REAR”: to output to a
power amplifier.
DIM (Dimmer) To change the brightness of the
display.
– “DIM-ON”: to dim the
display.
– “DIM-OFF” (z): to
deactivate the dimmer.
DEMO*1
(Demonstration)
To set “DEMO-ON” (z) or
“DEMO-OFF” (page 4).
A.SCRL
(Auto Scroll)
To scroll long displayed items
automatically when the group/
track is changed.
– “A.SCRL-ON”: to scroll.
– “A.SCRL-OFF” (z): to not
scroll.
LPF*2 (Low
Pass Filter)
To select the cut-off frequency
“78HZ,” “125HZ” or “OFF

Jan 28, 2010 | Sony CDX-S2210 CD Player

1 Answer

How do i adjust the treb/bass?


my initial reply was...On the function button you may need to depress it for 3 seconds to activate base, treble, balance etc But
then I found this, "Rotary Volume Control: The CD receiver uses a 7-way rotary volume control that increases and decreases the volume of the stereo from 0 to 35. The rotary knob also controls other audio settings such as Balance, Fader, Bass, Mid, Treble and preset EQ settings. In addition, the rotary knob allows you to scroll through and select your music tracks when the Music Search function is activated.
Cheers, this should help ya.

Jan 01, 2010 | Kenwood KDC-BT742U

4 Answers

Setting the clock of JVC KD-G125 does anyone know what and how?


to adjust the PSM (preferred setting mode) items, press and hold the select button (SEL) for 5 seconds..you should see one of the items DEMO (default item) displayed on the display window..press the Up/Down or Forward/Reverse buttons (^ or >>| or |<< ie.. it is the one you use to change the radio stations) to scroll to the PSM items DEMO-->CLOCK H-->CLOCK M-->L/O MODE-->AMP GAIN...when the PSM item you want to adjust displays on the window, CLOCK H for hours or CLOCK M for minutes for this case, use the control dial (volume knob) to change the setting...after adjusting the correct setting..press the SEL button again to end the procedure

Sep 06, 2009 | JVC AM FM CD DET FACE CAR STEREO

3 Answers

Thumping sound


You either have a bad ground from your amp to the vehicle or a problem with the amp. Where is the amp grounded? Do not ground an amp to a seat bolt or side panel on any vehicle. The weld points on the car itself cause issue with ground. Take the ground wire directly thru the bottom panel (floor) Check befor you drill! don't hit a wire/fuel line, etc. That will give you a solid ground. Keep your ground wire length to a minimum. 18" or less, and use the same gauge wire for ground as you do for power. Hope this helps

Jun 10, 2009 | Pioneer DEH-1600 CD Player

1 Answer

Setting the time in my alpine car radio


hold down the sound button until the settings pop up. then keep scrolling until you find clock stg. After you find this, click the play/pause button on the top left of the stereo and the hours will blink. then press it again and the minutes will. you change the number by scrolling with the volume button

Mar 11, 2008 | iLO XM-MP3-CD Car Stereo

2 Answers

Clock


Push the small button beside the 1.

scroll through the options with the volume dial until you get to "clock adjust" hit enter (top button) then adjust the hour with the volume knob. Hit enter again and adjust the minutes.

press ret (bottom button on the left to bring you back to the main confirugarion screen (should see clock adjust again) then press and hold esc. (middle button between ret and ent) until the regular playback screen comes back.

Nov 09, 2007 | Alpine CDA-9883 CD Player

Not finding what you are looking for?
Pioneer DEH-1600 CD Player Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Car Audio Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

xxxxxx xxx

Level 3 Expert

4706 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Are you a Pioneer Car Audio Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...