Question about GE 168952 Deep Fryer

1 Answer

DP16 power cord replacement

I need to replace a DP16 power cord for GE deep fryer, but am unable to find one

Posted by on

  • 5 more comments 
  • Anonymous Nov 23, 2008

    dp 16 power cord, i need one

  • aljr30 Dec 03, 2008

    We also have a short in the power cord for our GE deep fryer.

  • Anonymous Dec 28, 2008

    Need to find a replacement cord
    \


  • temalf Jan 27, 2009

    looking for DP 16 power cord for my deep fryer

  • Anonymous Feb 02, 2009

    I had my Deep fryer for 2 months and already the cord does not work. I tried different outlets, and it still doesn't work. It was a christmas gift, and

    now i'm hoping my brother can find the receipt.

  • Anonymous Feb 14, 2009

    lookingg for cord for this unit . Dose anyone have the answer?

  • Anonymous Apr 21, 2009

    Need replacement cord.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 2 Answers

Solution: Request one at 18002670516 GE cust service Part#227366 (akaDP16) need enough requests to make more for model#168952 fryer, Please cal!!
-Chuck-NJ

Posted on Dec 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No power lights will not come on no power


If your fryer has the DP16 cordset, this might solve your problem. Otherwise, have you press the reset button. It's hard to find, but it is there.

Solution for fixing DP16 Cordset for GE deep fryers: To begin with, you willl need to clean the electrical contacts on both the fryer and the cordset. They will be burnt from electricity arcing between the two when the cord is plugged into an outlet before connecting to the deep fryer. I used a dremel tool attachement grinder used for sharpening chain saw chains. It is cylindrical and fits in the holes in the cordset perfectly. You could use sandpaper rolled into a small cylinder, or whatever is available that will do the job. To open the flaps that cover the holes, insert a toothpick in the center hole of the cordset while you work. Make sure that both sets of contacts are completely clean before proceeding with the next step. Next, using needle nose plyers, make two tight coils of fine or extra fine (.032") resin core solder the same size as the holes in the cordeset. Press into place in each of the holes in the cordset against the electrical contacts. Spread the coils a little so they cannot fall out when the cordset is not attached to the fryer because the flaps will likely not close properly or at all. You can work the coils down so the flaps will close if you use the .032 solder, but they will still be a little loose, so they might jam the flaps open or partially open. This definitly isn't a UL approved method, but it will fix the problem completely. Happy frying!

Oct 21, 2010 | GE 168952 Deep Fryer

1 Answer

Need replacement cord set (DP16)


If you have your old cord, the following will probably solve your problem.

Solution for fixing DP16 Cordset for GE deep fryers: To begin with, you willl need to clean the electrical contacts on both the fryer and the cordset. They will be burnt from electricity arcing between the two when the cord is plugged into an outlet before connecting to the deep fryer. I used a dremel tool attachement grinder used for sharpening chain saw chains. It is cylindrical and fits in the holes in the cordset perfectly. You could use sandpaper rolled into a small cylinder, or whatever is available that will do the job. To open the flaps that cover the holes, insert a toothpick in the center hole of the cordset while you work. Make sure that both sets of contacts are completely clean before proceeding with the next step. Next, using needle nose plyers, make two tight coils of fine or extra fine (.032") resin core solder the same size as the holes in the cordeset. Press into place in each of the holes in the cordset against the electrical contacts. Spread the coils a little so they cannot fall out when the cordset is not attached to the fryer because the flaps will likely not close properly or at all. You can work the coils down so the flaps will close if you use the .032 solder, but they will still be a little loose, so they might jam the flaps open or partially open. This definitly isn't a UL approved method, but it will fix the problem completely. Happy frying!

Sep 28, 2010 | GE 168952 Deep Fryer

1 Answer

My ge deep fryer will not turn on


If your fryer uses the DP16 cordset, this is probably your problem. If not, find and press the reset button.

Solution for fixing DP16 Cordset for GE deep fryers: To begin with, you willl need to clean the electrical contacts on both the fryer and the cordset. They will be burnt from electricity arcing between the two when the cord is plugged into an outlet before connecting to the deep fryer. I used a dremel tool attachement grinder used for sharpening chain saw chains. It is cylindrical and fits in the holes in the cordset perfectly. You could use sandpaper rolled into a small cylinder, or whatever is available that will do the job. To open the flaps that cover the holes, insert a toothpick in the center hole of the cordset while you work. Make sure that both sets of contacts are completely clean before proceeding with the next step. Next, using needle nose plyers, make two tight coils of fine or extra fine (.032") resin core solder the same size as the holes in the cordeset. Press into place in each of the holes in the cordset against the electrical contacts. Spread the coils a little so they cannot fall out when the cordset is not attached to the fryer because the flaps will likely not close properly or at all. You can work the coils down so the flaps will close if you use the .032 solder, but they will still be a little loose, so they might jam the flaps open or partially open. This definitly isn't a UL approved method, but it will fix the problem completely. Happy frying!

May 15, 2010 | GE 168952 Deep Fryer

1 Answer

When i went to go use my deep fryer the other day


If it uses the DP16 cordset, that is probably your problem. If not, find and press the reset button.

Solution for fixing DP16 Cordset for GE deep fryers: To begin with, you willl need to clean the electrical contacts on both the fryer and the cordset. They will be burnt from electricity arcing between the two when the cord is plugged into an outlet before connecting to the deep fryer. I used a dremel tool attachement grinder used for sharpening chain saw chains. It is cylindrical and fits in the holes in the cordset perfectly. You could use sandpaper rolled into a small cylinder, or whatever is available that will do the job. To open the flaps that cover the holes, insert a toothpick in the center hole of the cordset while you work. Make sure that both sets of contacts are completely clean before proceeding with the next step. Next, using needle nose plyers, make two tight coils of fine or extra fine (.032") resin core solder the same size as the holes in the cordeset. Press into place in each of the holes in the cordset against the electrical contacts. Spread the coils a little so they cannot fall out when the cordset is not attached to the fryer because the flaps will likely not close properly or at all. You can work the coils down so the flaps will close if you use the .032 solder, but they will still be a little loose, so they might jam the flaps open or partially open. This definitly isn't a UL approved method, but it will fix the problem completely. Happy frying!

Mar 12, 2010 | GE 168952 Deep Fryer

1 Answer

I NEED A CORD- DP16 CORDSET I HAVE A --GE 168997 DEEP FRYER


You can find replacement cords for many counter top
appliances at most appliance and building supply stores. Try Ace, Home Depot, Lowes. Take the cooker with you to make sure you are getting the correct cord.

Dec 01, 2009 | GE 168997 Deep Fryer

1 Answer

I need to purchase the power cord with magnetic plug for my deep fryer. GE cannot help me with this part? Where can I find a new power cord?


If it is a DP16 cord, good luck with finding a new one, but if you still have the old one, the following might help,

Solution for fixing DP16 Cordset for GE deep fryers: To begin with, you willl need to clean the electrical contacts on both the fryer and the cordset. They will be burnt from electricity arcing between the two when the cord is plugged into an outlet before connecting to the deep fryer. I used a dremel tool attachement grinder used for sharpening chain saw chains. It is cylindrical and fits in the holes in the cordset perfectly. You could use sandpaper rolled into a small cylinder, or whatever is available that will do the job. To open the flaps that cover the holes, insert a toothpick in the center hole of the cordset while you work. Make sure that both sets of contacts are completely clean before proceeding with the next step. Next, using needle nose plyers, make two tight coils of fine or extra fine (.032") resin core solder the same size as the holes in the cordeset. Press into place in each of the holes in the cordset against the electrical contacts. Spread the coils a little so they cannot fall out when the cordset is not attached to the fryer because the flaps will likely not close properly or at all. You can work the coils down so the flaps will close if you use the .032 solder, but they will still be a little loose, so they might jam the flaps open or partially open. This definitly isn't a UL approved method, but it will fix the problem completely. Happy frying!

Aug 06, 2009 | GE Deep Fryers

2 Answers

Ge dp16 cordset


Ge customer service at 1-800-267-0516 needs to hear from enough requests and GE will refill DP16 (item#227366)power cords in stock at GE for Fryer model #168952. "There made to order with enough requests or complaints"-Cust. Serv.
So with this info, everyone please call with item number above model 168952 and state you need a new DP16.
Hope this is helpful!
Chuck-NJ

Jul 21, 2008 | GE 168952 Deep Fryer

2 Answers

It does not power on.


The cord is bad. We found that by jiggling the cord, the unit started to heat again. We are currently looking for a replacement cord for ours also.

Dec 17, 2007 | GE 168952 Deep Fryer

4 Answers

Fryer problem


The problem is with your cordset if it is a DP16, Here's how to fix it.

Solution for fixing DP16 Cordset for GE deep fryers: To begin with, you willl need to clean the electrical contacts on both the fryer and the cordset. They will be burnt from electricity arcing between the two when the cord is plugged into an outlet before connecting to the deep fryer. I used a dremel tool attachement grinder used for sharpening chain saw chains. It is cylindrical and fits in the holes in the cordset perfectly. You could use sandpaper rolled into a small cylinder, or whatever is available that will do the job. To open the flaps that cover the holes, insert a toothpick in the center hole of the cordset while you work. Make sure that both sets of contacts are completely clean before proceeding with the next step. Next, using needle nose plyers, make two tight coils of fine or extra fine (.032") resin core solder the same size as the holes in the cordeset. Press into place in each of the holes in the cordset against the electrical contacts. Spread the coils a little so they cannot fall out when the cordset is not attached to the fryer because the flaps will likely not close properly or at all. You can work the coils down so the flaps will close if you use the .032 solder, but they will still be a little loose, so they might jam the flaps open or partially open. This definitly isn't a UL approved method, but it will fix the problem completely. Happy frying!

Oct 26, 2007 | GE 168952 Deep Fryer

Not finding what you are looking for?
GE 168952 Deep Fryer Logo

Related Topics:

1,221 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Deep Fryers Experts

Paul Bade

Level 3 Expert

1392 Answers

Peter Hampton

Level 2 Expert

193 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Are you a GE Deep Fryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...