Question about Philips 32PF9964 32 in. Television

3 Answers

Problem starting a plasma

When i switch the tv on, it appears as though it is going to start i.e the green light comes on, then after about 10 seconds it switches itself off and the standby light flashes red. It takes 10 /12 times before it starts and is getting worse.

Posted by on

  • 2 more comments 
  • lillie69 Dec 03, 2007

    i changed the three capacitors but still the same problem

  • scolli88 Dec 14, 2007

    Hi.

    yes i have the same problems i changed the 3 caps and still no joy.

    only thing is the caps i got in mine are 2663, 2664 both 100µ/50v.and

    2662,1000µ/25V.this is what i dont understand as ive had mined from new and the caps are different.

  • Anonymous Jan 06, 2008

    hi again since the last time i now found the problem it was the transformer

  • jim533 Jul 17, 2008

    Yes, I am having the same problem with my 42PF9964 which is identical when it come the main power board. I changed out the caps (2662, 2663, 2664) and still NG. Any direction would be helpful. Thx.

×

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,130 Answers

When it looks like its going to start up and it dosent then its an indication that one of the sweeps didnt start up. When you hit the power switch, the power supply sends an ok signal to start up the horizontal and vertical oscillators. When these start up they go to there respective drive circuits and then the vertical will send a signal to the power supply to keep on going so then the horizontal circuit starts up and sends an ok signal to keep going so then the set comes ob,\. If one of the two doesent start up and stay running then the power supply shuts down. To troublwe shoot these sets you need a service manualo and a good multmeter and a scope wouldnt hurt slso. This set has no user servicable parts inside of her so you need to take the set to a pro to assist you in the repair. Good Luck

Posted on Jun 01, 2006

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

My one take too long to turn on, relay/green light on and off for hours before it can start, I use a hair dryer to heat it up, then it turn on faster

Posted on Oct 07, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same plasma TV and had the same problem. The problem is three caps. Change the cap 2663, 2664 both 100µ/25V and 2662,1000µ/25V. After you have changed them your TV will work again.

Posted on Apr 02, 2007

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After replacing power supply and resetting tv still only have green flashing light


Remove Mains Plug and press Standby switch from LED Panel for 30 sec. Press Input & Ch Down Switch from LED panel and plug in and start LED LED will start and "K" will appear on screen Press Ch Down & Vol Down switch at same time You will get 1/10 page on screen Go to 9/10 page by pressing left & right button from remote Select EEP and press Ok button from remote After 30Sec remove main plug and restart LED.

Dec 13, 2015 | Sharp AQUOS LC-32D44U 32 in. LCD TV

1 Answer

Yes I have a DP 50749 sanyo plasma tv 50 inch the green power led comes on for 20 seconds goes off. then it sounds like relay on the main power board starts a clicking noise Then it stops clicking...


This is likely a heat issue, and the CPU of the tuner is instructing the power board to switch it off for reasons related to over heating. Check that a fan ventilation improves the problem. The solution is not easy but maybe adding a fan to the tuner CPU can fix this issue.

May 07, 2014 | Sanyo DP50749 50 in. Plasma TV

1 Answer

When i go to turn the tv on the green light go on and then off. i did the coe test error code repeated 10 times


I found that by simultaneously holding down the remote control "power" button and "volume" button for about 30 seconds the blinking light would go out and a solid green light would come on. Even though the solid green light came on the unit would still not power up. After doing this several times however the unit did finally power up in a normal mode and appears to be working again

Jan 02, 2011 | Mitsubishi WS-55807 TV

1 Answer

Washing machine wil not fill - tries several times then stops and all lights except 4 go out


That would be the balance switch, should be located rear right under the main board. over time the switch becomes jamed in the on position and the machine always thinks its off balance. $4 to $10 for a new one.

Apr 14, 2009 | Washing Machines

2 Answers

42FD9954 philips plasma TV flashing LED it wont come on


The problem is in the standby power supply. the standby power supply generates the 9 volts and the 5 volts requird by the tv. If you measure the 9 volts source, with only the red light on, the correct voltage is 9 volts. However if the 9 volt measures 6.5 to 7 volts it is too low and the startup relays cannot operate. My set is a model 42FR9954/17S. In this set if capicator, 2603, is heated the voltage climbs to 9 volts and the relays work. If cold air is applied to the capicator the relays fail to operate. Replace capacitor 2503 and the problen is fixed. This capicator is: 47 Ufd, rated @ 450 volts, and is 20%.

Nov 08, 2008 | Philips 42FD9954 42 in. Plasma HDTV

1 Answer

Returns to standby


Green flashing 3 times = digital DC - DC converter fault
Red flashing 3 times = scan circuit fault

Oct 31, 2007 | Pioneer PureVision PDP-5040HD 50 in....

1 Answer

2 year old Phillips 42" Plasma TV won't turn on


Hi I had exactly the same problem, bought the above parts off ebay. The above solution worked and tv back to normal. the soldering is a bit tricky and there is a lot of screws holding the back on!

Sep 13, 2007 | Televison & Video

6 Answers

Philips plasma won't turn on first time


I have found this on a site and am in the proccess of trying to mend my plasma PF9964 as it started to take longer and longer until it stopped coming on. I've got the back off so I just need to un solder capacitors and replace. Here's the info I found. Bad power switch circuit General Comments If you have this problem with your Philips 32PF9964: When I switch the TV on, it appears as though it is going to start i.e the green light comes on, then after about 10 seconds it switches itself off and the standby light flashes red. It takes 10 /12 times before it starts and is getting worse. This is the solution: The problem is three caps. Change the cap 2663, 2664 both 100µ/25V and 2662,1000µ/25V. After you have changed them your TV will work again. You will find them easy if you unscrew the back on the plasma TV. Cheers, Mike

Jun 26, 2006 | Philips E-Box FTR9965 DTV Receiver

Not finding what you are looking for?
Philips 32PF9964 32 in. Television Logo

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75756 Answers

matt martin
matt martin

Level 3 Expert

1229 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Philips Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...