Question about Epson PowerLite 500C Multimedia Projector

1 Answer

No power to my Dreambox 500c cable receiver

HI
When i plug my power ac adapter to my Dreambox 500c cable receiver. The green light on the power adapter immediately goes out. There is no Green light on the Dreambox.

I would appreciate any help to fix the problem.

Silk

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Dreambox c500 no power

Posted on Mar 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need power cord and AC adapter for an Acer H236HL BID monitor


You may want to call Acer support for them to send you a new power cord and ac adapter. Acer technical support number is 1-800-816-2237

May 15, 2014 | Acer Multimedia Projectors

2 Answers

Mitsu hc3000 problem "red-green status light blinking and no input"


Heres what the manual says about REd / green lights

Unplug the power cord from the wall outlet and contact your dealer

And also this:

Check that the lens cap is removed.
It may take about one minute for the lamp to light up.
The lamp fails to light up on rare occasions. In such a case, wait for a few minutes
and then try again.
If the projector was turned off before the lamp was cooled down suf? ciently last time,
the fan may start rotating and the POWER button may not work after the power cord
is plugged. After the fan stops rotating, press the POWER button to turn back on the
POWER indicator.
Check that the intake vent is clean.
Set SCART INPUT in the FEATURE menu to OFF. (See page 25.)
Check that the lamp cover is closed. (See page 33.)
Check that the cables connected to the external devices are not broken.
When an extension cable is being used, replace it with the supplied cable for check. When
images are displayed correctly, add an RGB signal ampli? er to the extension cable.
Check the operation manual of the video device for its connection.

Mar 14, 2008 | Mitsubishi HC3000U Multimedia Projector

1 Answer

BROOKSTONE HDMI PROJECTOR 801143 DOES NOT CHARGE


The Brookstone manual claims it will fully charge after 3-5 hours, but it takes much longer then that. Mine does not indicate green light, but it seems it stops blinking red when its fully charged. After that it run on power directly from the ac-adapter.

If you keep it connected to the AC-adapter after it have stopped blinking red (do not disconnect it at all), it will start to run on the adapter and will not turn off. You will feel the AC-adapter gets hot while its running, something it does not while regular charging.

If it still dont stop blinking red after having it connected to power for 3 days, your AC-adapter is probably faulty. This happened to me, and after allot of research I found this replacement from a US seller on ebay (only five dollars included shipping).

http://www.ebay.com/itm/251623019268?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

Good luck with your projector. It a really cool little thing, but it has some design flaws.

Best regards.

Feb 17, 2014 | Brookstone HDMI Pocket Projector

3 Answers

Very faint horizontal lines moving from bottom to top of picture why??


Hello,
This is most likely the result of a "Ground Loop" If you are using the composite or component (RGB) inputs and experience these slow moving lines/artifacts it is caused by a voltage potential between the ground reference/pin of the projector and the video source.
There are several ways to correct this... 1) You can use a ground lift a (3 prong to 2 prong) adapter where the projector plugs into the AC power socket. 2) you can use a video "Hum Bucker" to isolate the ground potential between the video source and projector which is placed in series with the video feed to the projector. (very expensive) 3) If possible try plugging the projector into an AC outlet that is common to where the video source is getting it's power. For example have the projector and video source (receiver etc.) share the same AC power receptacle with a plug strip or similar device.

I don't know how your system is setup exactly... The ground voltage potential could be developing between components before the projector (not likely)

Good Luck!

SagerTronics

Oct 30, 2009 | InFocus ScreenPlay 4805 Multimedia...

4 Answers

Optoma EP772 lamp will not start...


try going direct connection dvd to projector .is your dvd upconverting to 1080p or just 1080i?let me know.

Aug 16, 2009 | Optoma HD70 DLP Projector

1 Answer

Projector shut down


Hi

Replace the lamp, or better yet try removing and reinstalling the lamp.;


Hope this helps

Nov 01, 2008 | BenQ PE8700 Multimedia Projector

1 Answer

GE Vivid i portable echo machine not powering up


It was a problem in ac adapter. I tried to plug in the ac adapter into the machine turning 90 degrees each time and at one specific position it turned on and battery also started charging.

Jun 14, 2008 | Multimedia Projectors

1 Answer

Unit will not power on


Company said it was defective. Sent back for exchange.

May 30, 2008 | ViewSonic PJ501 Multimedia Projector

2 Answers

Infocus LP70


its not geting power lust like mine

Dec 11, 2007 | InFocus LP70+ Multimedia Projector

Not finding what you are looking for?
Epson PowerLite 500C Multimedia Projector Logo

Related Topics:

1,254 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Multimedia Projectors Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68223 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5612 Answers

Are you an Epson Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...