Question about Dyna-Glo D-E37 Wall Mounted Panel Heater

2 Answers

Thermastat don't kick on until turned to 5 & then goes out if turned any lower.

This heater was bought from a yard sale but is in excellent condition, or so I thought. When I 1st hooked it up & turned it on, I could smell gas bad but I let it go & after about 10min or so the far left burner finally lit but it was the only one. I got a flashlight & looked in the back of it & could see that the little gas nipples were pretty much covered over with gunk. I pulled the plate off the bottom/front & cleaned them the best I could & used a small pc of wire to clean the holes out. It seems to be working better but still not right. Now all burners will light except the 1 second to the left. Also, when I turn the thermastat to turn it on, it has to go all the way to 5 before it'll kick on. At that point you can hear & feel it kick on but when you try to turn it down, it shuts completely off when you reach 4&1/2-5. It seems to be either all or nothing.

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 359 Answers

Have someone check your gas pressure that sound more like the problem you describe

Posted on Dec 17, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Dyna-Glo Master
  • 2,046 Answers

It would be the thermosat is faulty only working on high and shuting down too soon with no heat ?

Posted on Jan 14, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Induced draft gas furnace will not turn work

Check the 3-5 amp fuse on the control board of the Furnace, tell me if the fuse has a burn spot on it.

Dec 19, 2012 | Heating & Cooling

1 Answer


An excellent source for parts is Hope this helps you. you will need model number and part no. if you have it. Good luck and have a good year. Thank you.

Jan 03, 2011 | Desa International Blower Glow Warm Wall...

1 Answer

Bought model (I think this is model #) 29456 at yard sale; using it to heat garage -- do I need to vent? door open ok? or can I use ventless?

Hi and welcome to FixYa, I am Kelly

Anything that burns produces Carbon monoxide. There is no way to physically vent the space heater but you can leave a side door open for air. The key is to notice the signs of nausea, the lack of ability to do things requiring manual dexterity / clumsiness, dizziness or a headache when your using the unit. Also... it is a good idea to have someone check on you about every 30 minutes if your working alone in a garage. Make sure they know how to turn off the heater and how to open your garage door. (just common sense stuff)

Thanks for choosing FixYa,

Nov 28, 2010 | Reddy Heater-30-55,000 BTU Variable

1 Answer

I have a problem with my reddy heater 170t. it fires up runs untill it reaches set temp.but when it goes to restart the motor runs bacwards?after i manualy turn it off/on 2-3times it fires back up...

The thermostat is not the problem. The motor has a starter capacitot attached that gives the motor a burst of energy to get it going the right direction. It is not doing its job. The motor must be replaced.

Nov 27, 2010 | Reddy Heater-170,000 BTU Kerosene Deluxe

1 Answer

Bought heater at a yard sale & says oil filled heater but dont know how or where to fill??

The heater should be per filled with oil and sealed allyou should have to do is plug it in and waite about 15 or 20 min for the oil to heat up

Dec 01, 2009 | Heating & Cooling

2 Answers

Lennox Gas Frunace fires goes out, fires goes out, fires goes out

Check your thermostat anticipator setting. If you dont know how to do this don't try on your own or you may damage your thermostat.

Dec 12, 2008 | Honeywell Electronic Programmable...

2 Answers

Heater not turning on

the thermastat needs replaced!

Dec 09, 2008 | Reddy R70ET Utility Heater

Not finding what you are looking for?
Dyna-Glo D-E37 Wall Mounted Panel Heater Logo

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dyna-Glo Heating & Cooling Experts


Level 3 Expert

2046 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers


Level 1 Expert

10 Answers

Are you a Dyna-Glo Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides