Question about Air Tools & Compressors

1 Answer

Error code I no longer have the warranty. If it was that simple I wouldn't have signed on to this website for help. I've got two options now. Either just toss the printer in the trash, or try to fix it myself, and if I fail THEN toss it in the trash. So bottom line is I got nothing to lose now by tearing into the gizmo. Is this possible at all or totally out of the question?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,472 Answers

You said the unit is 3 months old correct? then it would still be under the manufacturer warranty. It is possible for it to be repaired did you go through the steps I gave you?

Posted on Oct 17, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Owners manual

There are very few places that carry Craftsman parts and manuals other than Unfortunately your manual is no longer available through them and the only reference to the manual (part number SI-30-14-5-A) on a web search is to the Sears website. Most of the parts for your compressor are available on that website. If you have a specific question you can post it here and I'll try to answer it.

Jun 24, 2012 | Air Tools & Compressors

1 Answer

I have a Campbell Hausfeld WL651500AJ and it wouldn't go past 50PSI. I went ahead and looked up the issue and found many people with the same problem, most of which people said the reed valve were the

Air compressors generate a huge amount of heat compressing air. It is not unusual for the copper tube to be too hot to touch after three minutes of running. Replace the tube and see if it fixes your problem. Another common cause of only getting to 50psi is a bad seal between the piston and cylinder. There is no need to use sylicone to seal anything on the pump, just make sure all the gaskets are in good condition and all screws are very snug, don't overtighten as stripped bolt hole threads are a bear to fix.

Dec 23, 2011 | Campbell Hausfeld 26 - Gallon Air...

2 Answers

I just purhcased this air compressor and cannot get any pressure to bulid in the tank. Even when the drain valve has been closed, there is still air being released. Any thoughts?

This a new machine correct. Did you let it run with the valve open for the 15 minitues this seals and lubes the pistion Ihave the same machine and i know how noise it is aswmeing the pump is pumping there are 3 other paces it could be leaking.The blow out valve the regulator or the inlet hose if the drain is closed.You are going to have to run your hands around the the regulator area and the hose something must be leaking and you won't be able to hear it. It dose have a one year warranty mabey you just got one with a ploblem mine work find i've had it for almost two years with no complantes good luck

Jan 15, 2011 | Porter Cable C2002 150 Psi 6 Gal...

3 Answers

My Hitachi EC12 builds pressure, shuts off, then air escapes through the relief valve for a period of time, sometimes shorter sometimes longer. If longer, the compressor switches on again, but has trouble...

the problem is in the check valve where air enters the tank.when leaking it lets air pressure up to the air piston causing the motor to stall upon restart.replace check valve.average cost of part 15 to 30 dollars.simple fix

Mar 29, 2010 | Hitachi EC12 Portable Electric 2hp Air...

1 Answer

I have a CH WL611701AJ compressor. The motor starts and runs for approx 15-20 seconds before blowing breaker. I have replaced both capacitors, still blows breaker. Removed piston to allow motor to...

This may seem a bit simplistic but how are you hooked up to the outlet? Are you using an extension cord or is the compressor plugged in only using the supplied power cord?
If you are using an extension cord then you are going to pop the breaker every time you use it. Infact the manual states

"Never use an extension cord with this product. Use additional air hose instead of an extension cord to avoid power loss and
permanent motor damage. Use of an extension cord voids the warranty."
Air compressors don't like extension cords.
It simply draws to much for an extension cord to handle.
Depending on whether or not your warranty is out there is a simple solution. Find the biggest gauge extension cord you can

If your not using an extension cord and it's ran in the past where it's plugged in now then check the circuit because there must be new draw on the breaker

You said the breaker is 20amp. correct? The compressor should be run on a breaker dedicated to the compressor only.

Even though you should use a longer hose instead of a longer power cord you can get away with it. But forget about wire gauge size you need to think wire diameter. The extension cord I made for my compressor is approximately 3/4" thick. That is the only way I was able to use an extension cord on mine. A good place to get that size cable is a boat supply store. The cable used for shore power on boats works.
Hope this helps but if not please let me know and I'll try and help anyway I can to solve your problem.

Nov 15, 2009 | Campbell Hausfeld 28 - Gallon Air...

1 Answer

Unable to register

Changes were made to the website. Start at and select the customer support option that appears at the top right of the page. You will see the option to register your products on the left under heading of products and services. Click on the product registration option. Sign in as a guest and you should be able to register your products. You also have the option of signing up a a member.

Hope this helps,

Dec 28, 2008 | Air Tools & Compressors

1 Answer

Cant register my black and decker tools onlne

Changes were made to the website. Start at and select the customer support option that appears at the top right of the page. You will see the option to register your products on the left under heading of products and services. Click on product registration. Sign in as a guest and you should be able to register your products. You also have the option of signing up a a member.

Hope this helps,

Dec 20, 2008 | Air Tools & Compressors

1 Answer

Error code 5100

being that it is only 3 months old i would have it serviced under the manufacturer warranty. 1-800-OK-CANON call that number and you can locate the nearest authorized service center and the service will be covered. If you still need assistance let me know. Please take a moment to accept and rate my original solution as I strive to provide fast and accurate service.

Oct 16, 2008 | Air Tools & Compressors

Not finding what you are looking for?
Air Tools & Compressors Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Air Tools & Compressors Experts

John Trevino

Level 3 Expert

1383 Answers

Brad Brown

Level 3 Expert

14725 Answers

james allen
james allen

Level 2 Expert

109 Answers

Are you an Air Tool and Compressor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides