Question about Kenmore Oasis HE 27082 Top Load Washer

1 Answer

I try to start the washer and I get a "dL" reading

I put half a load in the wash and hit normal wash (40 minutes on Auto), it sounds like it starts to fill for a moment, then stops, beeps and flashes a "dL" on the screen. The dial blinks and it beeps every few seconds. I tried unplugging it and plugging it back in, but that didnt work either. I noticed that the latch didn't lock and assume it has something to do with that. Anyone with a clue please respond.

clotho20@hotmail.com

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 62 Answers

Usually a control board, common problem

Posted on Oct 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi! We have Kenmore Elite he3t. We noticed water in the washer today after a complete cycle so we ran the rinse and drain command on it. I tried to begin a new load on a normal wash cycle and it will...


Hello and welcome to FixYa


DL f is a door lock error and is caused due to an issue with the door lock when it is unable to lock/unlock. Please check the door lock mechanism/door switch assembly and replace the part that has gone bad so that the issue is resolved. Please get back to me if you have any other questions.


Kevin

Aug 30, 2011 | Kenmore Elite 45986 Front Load Washer

2 Answers

Kenmore elite model # 110.45088400. We set a cycle, washer starts beeping and reads F then blinks to DL. We hit pause to clear then try to restart while it makes clicking sounds and it continues to read...


Hi from retired Englishman in SW France,

'DL' stands for Door Lock error. There is likely to be a problem with either the door solenoid/lock or the 'door closed' sensor requiring a service engineer's attention I suggest. Sorry ;-0(

If this has assisted and/or clarified the situation for you please consider a 4 thumbs up on our rating.
Thanks and good luck!
John C

Aug 24, 2011 | Kenmore Elite 45986 Front Load Washer

1 Answer

The digital timer skips 9 minutes out of the wash cycle. After starting the normal 140 degree wash cycle (46 minutes) the washer will start and wash normally until it has counted down to 41, then it...


hi shotgun - sometimes the mieles with auto adjustment functions do make changes to the wash time - usually based on a smart sensor technology.

Unfortunately I have no data or information for your particular model, I have info on earlier & the latest models only. In hindsight what this function does is adjust water levels based on the load weight or amount of the wash, the computer then calibrates the water levels and accordingly the amount of time to wash.

Eg - 4 kg load would be longer than say a load 1.5kg to process - if can understand this concept. However I cannot be 100% certain it applies to your particular model, if the user manual is availbel it may just pay to read thru in case it applies to the washer.

Jun 21, 2011 | Miele Super Novotronic W1986 Front Load...

1 Answer

Washer reads dL f and door stays locked even


try to start another cycle then hit cancel and cancel again and it usually unlocks the washer

Apr 24, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Error message


Hit cancel the amount of minutes will stay the same and then hit the start button again.

May 13, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

WFMC3200UC stops half way through the cycle and wont finish


sounds and smells like a heating problem if the appliance is not heating it will not complete the cycle and as the detergent starts to break down it makes the appliance smell

Mar 12, 2009 | Washing Machines

1 Answer

Code F 40


Hello homefolks
Welcome to fixya.
I'm Huuum and happy to assist you,



You said, Your washer starts to wash and code come up it stop then starts runs for a
few minutes then code comes up again and does this over and over
can't finish a load. Model # 2709

Sounds like we need to try to reset the system!

Huuum At your service!
Lets try this,
Like with an error code.
This can reset the system if it is electronic!
Unplug the washer and wait a 5 minutes then restart it.
If you can't reach the plug, use the breaker to cut the power for 5 minutes.

It's like rebooting your computer when its acting strange!
Usually it corrects some error problems if they are not serious.
Or they are sometimes just a glitch.

Let me know how it works! Waiting for your reply!
Please remember to leave a rating when you are done!
thank You huuum




Sep 25, 2008 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Whirlpool catalyst washing machine won't start, but lights up


sounds like the ground wire needs to be tightend

Mar 26, 2008 | Washing Machines

Not finding what you are looking for?
Kenmore Oasis HE 27082 Top Load Washer Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Fred Sops

Level 2 Expert

271 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...