Question about HP Printers & Copiers

1 Answer

Sticker has got stuck on roller - HP Printers & Copiers

Posted by on

  • rwebbie Oct 18, 2008

    we tried that but it wont let the paper through the roller thanks

×

1 Answer

Try to print a piece of paper, then the stick might stick on the paper bein inserted

Posted on Oct 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

.comHP C4180 I think I


Unplug the printer from the power and press and hold the power button down for 30 seconds or so. Then turn the printer around so that the back is facing you. Look for two thumb release latches to open the back end view of the rollers. you should be able to open the hatch in the back to get an unobstructed view of the paper rollers. Clear out any paper jambs in this area. Then turn it around with the front facing you and put your fingers in the groove of the plastic panel right above the fold down tray where the paper comes out and pull the hatch downward towards you. This provides a front view of the inside area where the cartridge carriage goes back and forth. Clear and remove any paper or debris in this area. Then plug the printer back in and turn it on, and it should rotate the paper feed forward before winding backward to the starting position. Leave the hatch in the front open or lean downward so you can see the rollers and turn it on and off again to watch and see if anything is stuck on them (like a sticker or label). If you see something stuck there that appears when the rollers roll forward turn the power off to stop it in motion so that you can reach in and remove it before its rotated towards the back.

Jul 06, 2011 | HP Photosmart C4180 All-In-One InkJet...

1 Answer

Canon ix4000 printer. Paper jam caused by sticky label, came off backing, stuck to roller. Normal paper jam cures not effective.


This seems to be fault in the transport of the paper in the rollers. So since you have used adhesive sticker printing, it is possible that some glue has got clogged into the rollers.So use a good clening of the rollers using methyl spirit. also check to see asthere can be some jammed paper in the rollers or the mechanism.
So start this work only if you are mechanically able with the right tools.
Remove the covers to get access to the mechanism . Remove the motor drive assembly , the fitting of the motor to the mechanism. Once this is removed the rollers can be turned manually so that you will be able to feed a paper to see the progress of the movement while studying if there is any obstruction or damage to the paper.
There is a in-detect sensor, usually an opto-coupler , make sure this is not clogged or dirty as this IR detection feeds the signal to the processor for starting the motor drive feed.
Reassemble but make sure the rollers are aligned to be in equal gap to feed the paper without a side pull. Now you must print and see if the fault has changed. If not repeat the above work to confirm the area of obstruction.

Mar 30, 2011 | Canon PIXMA iX4000 InkJet Photo Printer

1 Answer

I have some paper stuck how can i remove it


This seems to be fault in the transport of the paper in the rollers. So if you have used any adhesive sticker printing, it is possible that some glue has got clogged into the rollers. If not there can be some jammed paper in the rollers or the mechanism.
So start this work only if you are mechanically able with the right tools.
Remove the covers to get access to the mechanism . Remove the motor drive assembly , the fitting of the motor to the mechanism. Once this is removed the rollers can be turned manually so that you will be able to feed a paper to see the progress of the movement while studying if there is any obstruction or damage to the paper.
There is a in-detect sensor, usually an opto-coupler , make sure this is not clogged or dirty as this IR detection feeds the signal to the processor for starting the motor drive feed.
Reassemble but make sure the rollers are aligned to be in equal gap to feed the paper without a side pull. Now you must print and see if the fault has changed. If not repeat the above work to confirm the area of obstruction.

Mar 26, 2011 | Lexmark Printers & Copiers

1 Answer

While copying labels a label became stuck to the drum roller...how do I clean it?


If it is on the photo receptor drum (mirror finish), it will likely not survive cleaning and will have to be replaced. If you mean any roller in the paper path, you can use a solvent such as 'Oops' to remove the sticker and then thoroughly remove any remaining adhesive otherwise you may have a new jam to deal with.

Mar 04, 2011 | Canon imageRUNNER 210S Copier

1 Answer

Paper stuck or jam in rollers


This seems to be fault in the transport of the paper in the rollers. So if you have used any adhesive sticker printing, it is possible that some glue has got clogged into the rollers. If not there can be some jammed paper in the rollers or the mechanism.
So start this work only if you are mechanically able with the right tools.
Remove the covers to get access to the mechanism . Remove the motor drive assembly , the fitting of the motor to the mechanism. Once this is removed the rollers can be turned manually so that you will be able to feed a paper to see the progress of the movement while studying if there is any obstruction or damage to the paper.
There is a in-detect sensor, usually an opto-coupler , make sure this is not clogged or dirty as this IR detection feeds the signal to the processor for starting the motor drive feed.
Reassemble but make sure the rollers are aligned to be in equal gap to feed the paper without a side pull. Now you must print and see if the fault has changed. If not repeat the above work to confirm the area of obstruction.

Oct 30, 2010 | HP Deskjet 870cse Printer

1 Answer

Sticker got stuck on red bar inside


You need to remove the fuser to get access, If you try to dig it out with anything you risk tearing up that red roller, it's pretty soft. You could replace the fuser, around $75.00, but if you take it out you can probably remove the sticker.

Aug 31, 2009 | Brother HL-2040 Laser Printer

1 Answer

I have a canon pixma mp210 series printer and on the printer's screen it comes up with e 2 3 as soon as i turn it on what does it mean and how can i fix it?


E23 Paper feed error

A piece of paper may not be jamming the rollers, but something small, such as a sticker or, in my case, a tag I cut off of a shirt and set on top of my printer, may be stuck under the roller.

Take something stiff and push it under the roller from inside the printer. As soon as you can see it from the other side, remove it and restart the printer.

power on the printer and force a single sheet of paper through the rollers


Mar 19, 2009 | Canon PIXMA MP210 Photo All-In-One Printer

1 Answer

Paper feed problem on Epson C87


In view of vk_malik's lack of interest in this problem, I think we may declare it "solved by poster"

Nov 24, 2008 | Lexmark X644e All-In-One Laser Printer

4 Answers

Paper Jam


i did exactly as iamzwalrus said and it fixed.go with that if nothing eles works.

Apr 24, 2008 | Canon PIXMA MP210 Photo All-In-One Printer

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts

kakima

Level 3 Expert

96576 Answers

k24674

Level 3 Expert

7987 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...