Question about Car Audio & Video

2 Answers

Blown resistior in a hifonics brutus bxi 1606d

Hi i have a hifonics brutus amp that i was told a resistor was blown can you tell me how to fix it or can you tell me someone that can fix it

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 218 Answers

You haven't said what is wrong with the unit. If it isn't turning on then I would be willing to bet you have more than a blown resistor to deal with. I agree with the other poster who said you should take it to a qualified repair guy. I think that is your best bet if your knowledge of electronic repair is so limited that you cannot tell the difference between a resistor and a transistor. Good luck.

Posted on Nov 11, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 341 Answers

If you can point it to me in the schematic diagram I might be able to help you. But I suggest you bring it to a qualified audio electronic technician if you still value it. cheers!

Posted on Oct 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need mosfets for hifonics amp sfp50n06


That is a Semiwell part I believe. It is an N-Channel power mosfet. Go look on their website they may have an alternate part you can use.


Dec 18, 2009 | Hifonics Brutus BXi 1206D Car Audio...

1 Answer

Hifonics bxi 1606d


you could just take some out of some other electronics because all they do is reproduce sound so there is litteraly no power going through

Jul 04, 2009 | Hifonics Brutus BXi 1206D Car Audio...

1 Answer

Bxi 1606d amp it turns on power up but no sound


Well i sounds like your amp is shot. Or you have the subs wired incorrectly to the amp. Each amp is different in stability with ohm loads and each amp performs differently at each load. Sounds like it was wired at the wrong ohm load in the past or it came defective from factory. Definately send it back if u just got it.

Jun 09, 2009 | Hifonics BXI 1606D Car Audio Amplifier

1 Answer

Hifonics brutus 2000 watt help??!!??


If an RCA took a dive your amp has most likely seen a very nasty input spike and may never be the same as its circuitry has been damaged.....sorry

Mar 09, 2009 | Hifonics Brutus BXi 1206D Car Audio...

1 Answer

2 4ohm dvc subs to a bxi 608 ( 600watt mono)


take the positive on the sub and run a wire to the other positive the run a negative to the other negative then to your pos and neg on the box do the same on the other side then tie your two positives and two neg together and you got 1ohm and that amp willl handle it all day

Jan 29, 2009 | Hifonics Brutus BXi 606 Car Audio...

1 Answer

Hifonics BXI 1606D problems


it may be a wiring problem you need to make sure all the speaker positives and negatives are correct. I sell alot of hifonics amps and have never had 1 do that. it may also be a bad rca cable. if it only does it when you use the filter i would say not to use it also make sure the gain is no more than 3/4 turned up and the bass boost no more than 1/2. if you have a dif amp try a temp setup using it and if it still does it its a wiring issue. also try 1 speaker at a time on the hifonics and keep adding 1 till it comes back it may be a bad voice coil on 1 sub .

Jan 08, 2009 | Hifonics BXI 1606D Car Audio Amplifier

4 Answers

No sound in my Hifonics Brutus BXi 1206D amp


Have you confirmed that you have a good signal feeding the amp?

Have you confirmed that the speakers are in good working order and don't have any breaks in the wiring?

Jan 01, 2008 | Hifonics Brutus BXi 1206D Car Audio...

1 Answer

My amp turns on then off while it slowly blows the fuse out


If I were a guessing man, I'd guess that you had your amp hooked up in a bridged configuration. And also that you connected your two speakers in parallel (plus to plus and minus to minus). And if I were to further guess, I'd guess that you have a blown amp now because of what I mentioned above. Sounds like you need to spend some quality time with your favorite electronic repair shop. Good luck.

Feb 23, 2007 | Hifonics BXI 1606D Car Audio Amplifier

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

454 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4724 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

63291 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...