Question about Canon SmartBase MP730 All-In-One InkJet Printer

Open Question

My canon smartbase MP730 Photo has stopped working completely

I switched it off one night and when I tried to switch it back on the following day.... nothing happened.... no hum... no flashing lights... no error codes... nothing... just totally dead. I've replaced the power cable with one that I know works, however it still doesn't do anything. I've plugged something else into the power socket and that works. So I know it is something inside my printer... Please help.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
tutopian
  • 57 Answers

SOURCE: canon smartbase mp730

Have you tried doing some maintenance like nozzle check,printing head alignment,clean the nozzles if not then try it by going into control panel - printers and faxes - where you see your mp730 right click and go to properties then click on the last tab which would be maintenance.Try those options if none worked then u might have to replace you print head and that should work

Posted on Nov 27, 2007

Ad
battlesmith
  • 382 Answers

SOURCE: Prints some blank pages

Hello Mike,
Please try to refill the catridge and if it dint help you then replace the Catridge ,which will surely pay off you..Thank you...

Please Post on how things turned or for further assistance..!!

Regards!!...

Posted on Jul 24, 2008

SOURCE: Canon SmartBase MP730 Photo Printer producing

sounds like your mechanism is really unhappy..is this still under warranty, by chance?




Posted on Aug 20, 2008

  • 421 Answers

SOURCE: ERROR SIGNAL CODE 5 FLASHES

Error also refers to the EEPROM for the printhead. I would reset the EEPROM and see if that helps.

Printer servcie manual here and it will show you how to do it:

http://www.tradebit.com/filedetail.php/4593231-canon-pixma-ip4200-printer-service-manual

Hope that helps

Posted on Nov 14, 2008

  • 2 Answers

SOURCE: Smartbase MP390 Printer - error ##345

canon smartbase mp390 error ##345 check printer can anyone help me

Posted on Feb 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Volvo 1998 S70 headlight and indicators won't always turn on


I have had this happen before - this is the multifunction switch on the steering column. The one on my Ford took about 10 minutes to change (two bolts). My problem - I would turn my lights off, then turn them back on and nothing, then they would suddenly pop on. after a bit my lights would not come on at all. I had to drive with my Flash to Pass lights for a couple of days when driving at night.

I hope this helps!

Aug 13, 2012 | 1998 Volvo S70

1 Answer

In sinkerator will only "hum" and not run to grind food


On The bottom of the unit there should be a place to put an allen wrench. Unplug unit, Insert wrench and turn the wrench back and forth this moves the blades if the blades move freely then nothing is stuck. If wrench does not move freely, with flash light inspect inside of disposal (the rubber flaps are usually removable to gain better eye site) if objects (bones, utensil, etc) are noticed remove them and try the wrench again if now freed problem solved. If wrench turned freely from the beginning and motor still hums. Replace disposal.

I hope this has answered your question, please rate how helpful the answer was. Good Luck and Have a great day.

Apr 03, 2010 | Ace Hardware InSinkErator Badger 5, 1/2 HP...

1 Answer

Acer Aspire One 6 Cell Battery Problem


you got a bad battery. If your old battery works fine, and the new one wont hold a charge, Take it back to the store and get another.

Dec 29, 2008 | Acer Aspire One AOA110-1626 Notebook

1 Answer

Headlights wont turn on.


relay somewhere ,??but where ?try looking under bonnet(hood)

Dec 17, 2008 | 1989 Pontiac Firebird

1 Answer

Fujitsu Siemens Amilo Pro V2055 laptop power on problem


Check to see if the ram is securely in place. (that will cause a pc to not boot, usually there is a beep code tho)

Oct 06, 2008 | Computers & Internet

1 Answer

Frigidaire dishwasher does not clean


the start switch in the motor is probably bad,it could also be the motor relay.if you can get to the motor run the unit and while it hums try to turn the motor.it also could be something is stuck in the motor let me know.

Aug 13, 2007 | Frigidaire 24 in. PLD2850 Built-in...

1 Answer

My dryer doens't start up


Depends on if you can hear any noise when you hit the start button or turn the knob. If there is a hum or some sound then could be belt or motor problems. If there is no sound dead, then you are checking the right area, there are kill switches in different places on dryers. one is like you checked the door switch, and another may be in back when you open the cover to check. Maybe fallen out of place. These sw. are for your safety and sometimes they malfunction. Hope this help!

Aug 12, 2007 | AEG T57800 Electric Dryer

Not finding what you are looking for?
Canon SmartBase MP730 All-In-One InkJet Printer Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

old marine
old marine

Level 3 Expert

2128 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...