Question about Toshiba Satellite A135-S2276 Notebook

Open Question

My mother bords smd chip does not work so display of screen does not appear

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The video card is not working.


If you can afford mother board change than go for it, but if not care fully follow the instructions. 1. open the mother board. 2. remove the heat sink. 3. see the nvidia MCP67MV chip. 4. Heat it with Torch, mobile lamination gun or you can use SMD soldering Station. 5. Boot it!
But this method only can stay for a month.!!!

Feb 16, 2011 | Acer Aspire 4520-5582 Notebook

1 Answer

Acer 5536 shows only black screen and does not go to vista mode


The problem is with the video chip of the laptop. for fixing it you need to reball the IC or you can do a trick. 1. Open the motherboard. 2. Pull out heat sink 3. search for nvidia display chip 4. heat the chip with heat torch or SMD soldering gun
Boot It.

Feb 08, 2011 | Acer Aspire 5536-5224 Notebook

1 Answer

Monitor will not turn on


First check your num lock key on key bord if it is on off when you press num lick key then your dispaly is working fine means you need to change screen resolution.
For that when you power up the computer press F8 key then enter in enable vga mode.then go to display property and change screen resolution to 1024*768 or 800 *600.
Also when you power up the computer press F1 or F2 or 'del" key to enter in bios then load optimal defaults also check your harddisk is detected .Disable your satat option in bios .then save settings then check.
I f you not able to enter in bios then Refix your ram.If still face problem you need to reset bios .
For that you have to open laptop cover in back then pull cmos cell from mother bord for 5 minutes then refix it then check.

Jul 27, 2009 | HP Pavillion dv9740us Notebook

1 Answer

Power Button wont do anything


First check your num lock key on key bord if it is on off when you press num lick key then your dispaly is working fine means you need to change screen resolution.
For that when you power up the computer press F8 key then enter in enable vga mode.then go to display property and change screen resolution to 1024*768 or 800 *600.
Also when you power up the computer press F1 or F2 or 'del" key to enter in bios then load optimal defaults also check your harddisk is detected .Disable your satat option in bios .then save settings then check.
I f you not able to enter in bios then Refix your ram.If still face problem you need to reset bios .
For that you have to open laptop cover in back then pull cmos cell from mother bord for 5 minutes then refix it then check.

Jul 27, 2009 | IBM ThinkPad T60 Notebook

1 Answer

To startup, I have to press to On/Of button 2x or even more. Sometimes, the startup begins, but more and more, nothing happens. It seems that even the bios won't startup. This problem with 2 of these...


Frist Rfix your battery and RAM memory.
then check if problem still remains then you have to reset bios setttings .

For that you have to open back side of laptop.
Then you find mother bord chip set.
Pull cmos cell from mother bord for 15 seconds then refix it then check.
you can refix Battery and RAM from back side there is 2 small plate RAM plate is up on battery plate.Let me know if you have any confusion .
Thanks.

Jul 16, 2009 | Fujitsu Siemens LifeBook E4010 Notebook

1 Answer

Password reset problem


u have to pull your cmos cell from mother bord 15 minutes.so it reset.
Open the back side of laptop then u find motherbord chip on it then pull cmos cell for 15 minutes

May 20, 2009 | IBM ThinkPad T30 2366 Notebook

1 Answer

Philips x57 distored / flikering screen


The problem is the pathway from the chip to the internal display. The Nvida chip has several output lines, many of which go to the external monitor but many also go to the internal display connector. I had a case recently where the screen worked fine until the customer opened the display past 90 degrees. What was actually happening was that enough presure was being applied by the internal connector to lift the mother board connector off the mother board. Apparently the factory solder job wasn't too good. We were lucky in that we used a high intensity heat source which remelted the solder on the connector. Whoever was dilligent enough to be to test your screen and cable should be able to trace the signal from the chip out.

Mar 23, 2009 | PC Laptops

2 Answers

Display blinking and turn in to white color with black lines


no its not a driver you have a video chip getting ready to fail.on the v2000 it intergrated in to the mother board. soon you will be joining many other compaq v2000 and m2000 owners in the search for a mother board compaq has updated part numbers it a whole differant board for these units due to having a common failure rate of the original mother boards.Compaq know there was a over heating of the video chip that leads to failure but has not offered any assistance to there customers. john@johnslaptops.com

Feb 17, 2009 | HP Compaq Presario V2000 Notebook

1 Answer

D630. LCD and external monitor does not display.


If its integrated and damaged then You would have to replace the mother bord (pricey)
have You tried reinstalling the video driver?

Alternative would be to get an external video card if rest of the mother board is ok

Jul 18, 2008 | Dell Latitude D600 Notebook

Not finding what you are looking for?
Toshiba Satellite A135-S2276 Notebook Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba PC Laptops Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

john smith

Level 2 Expert

366 Answers

Are you a Toshiba PC Laptop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...