Question about Hotpoint Aquarius WD640 Front Load Washer/Dryer

4 Answers

Hotpoint wd640 f-05 and f-11 error codes washer does not empty

Help please think it requires a new pump please confirm

Posted by on

  • Angelblue Feb 19, 2009

    I have a Hotpoint WD640T washer dryer. It is flashing error code F-05, we have removed the pump and got 63p out of it but the error code is still flashing, can anyone help please.

  • zbeven Apr 04, 2009

    Hiya I have had the same problem, is it expensive to repair, f-05 code flashes and wash stops, cleaned filter, checked pipes not blocked, filter was clogged but ok now, then f-11 flashed up, regards zoe

×

4 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 160 Answers

F05 say pump blocked or pressure switch fault. whereas f11 say pump cannot be activated... so either an open circuit pump or fauty pcb..

Posted on Feb 22, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi, I had the same problem (F11), and ended up having to buy a new pump (£22) which did the trick. What was annoying was that my washing machine was only just over a year old and the old pump has become rusty!

Posted on Jul 17, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 206 Answers

Take the back of the machine off.
You will need to try and tilt the machine forward or lay on the floor.
The bottom right you will see the pump witha pipe from the bottom of the drum.
Undo the plastic circlip with a small screwdriver by prising it apart. Then undo the clip onto the pump motor. Once undone check to see what rubbish has been collected. Empty by clicking the plastic and removing the floating ball ( which looks like a pingpong ball ) you will more than likely find old socks , handkerchiefs or other small items lodged and stopping the water pumping out
Just reassemble and Refit in the reverse to taking off.

Posted on Sep 21, 2014

  • Dai Boyce
    Dai Boyce Sep 21, 2014

    Forgot to mention , if you have a small tray put it underneath as a bit of water will come out of the system and the pipework you remove.

×

The f 05 error is a blocked filter

Posted on Oct 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint Aquarius wm750 won't fill with water


Dear Chris.

Here is offered a list of fault codes Error Codes Hotpoint Service

How to understand fault codes
Identifying Hotpoint or Indesit Error Codes

Hot Point Manual Link
Download Manual Hotpoint Service



It is possible your water supply is to low or your screens may be blocked at the inlet attachment to the washer. The other scenario a sticky or failing pump solenoid ; by which a direct replacement of the pump assembly may be required. Try to lubricate and actuate valve by hand if possible.


Fare Well.

Dec 28, 2014 | Hotpoint Washing Machines

1 Answer

What is f4 and f7 error code


F04 Error code is "Pressure switch jammed on empty"
F07 Error code is "Heater relay stuck"

Both would require you to dis-assemble the washer to get to each part for checking / replacing.

http://www.hotpointservice.co.uk/help-and-advice/error-codes/

Sep 03, 2014 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

My hotpoint wt640 will not empty and has an f11 code


Hi


Error F11 means that F11 - No hot fill.The ambient temperature is likely to be below freezing possibly due to the pipes being frozen. Also check that the taps are on or if the drain hoses are kinked. This may also have happenned if the washer is not draining. It may have happenned due to drain pump is not working. Try and check the drain pump, if the connections to the pump are fine. Please post back for further assistance.

Daniel

Jul 25, 2010 | Hotpoint Washing Machines

1 Answer

Error code 51? F & F intuitive washer


Hi just read your posting.Error code 51 means you have a Recirculation Fault.This means while the machine is filling or washing it loses water.Error code 37 means you have Pump Block error which means the machine is not draining.Please look under the machine to the front right and you should see a pump with a red or black fan attached.Can you confirm this please? I think there is a problem with your diverter valve and the information on your type of pump will help me rectify this problem for you.Please reply with additional information on the type of pump in your machine.Looking forward to your reply.

Jul 01, 2010 | Fisher and Paykel Washing Machines

1 Answer

Error code


H20 indicates incoming water supply problem.
Check that the water is fully turned on.
Check the inlet hose/s for kinks or restriction.
Make sure there is a good pressure of water to washer.

Please rate my solution.
Thankyou..

Jan 31, 2010 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Repair manual for hotpoint wt960p


The error code does not mean that the pressure switch is faulty, it is indicating a fault that affects the function of the switch.
The problem is actually a blockage in the pump or pump filter.
To rectify the problem, do the following.
Remove lower rear panel of washer.
Remove large black hose on bottom of drum.
Remove and clean plastic filter inside hose.
Remove hose onto pump, and check for blockage or obstruction hers as well.
This should solve the problem
Please leave feedback for my solution.
Thankyou.

Jan 19, 2010 | Hotpoint Washing Machines

1 Answer

Hotpoint Ultima Super Silent WF865. I'm getting error code F04 there's water in the machine and it's stopped.


Error code F04 indicates pressure switch jammed on empty.
Remove the lower rear panel of washer.
Remove the large black hose fastened to bottom of drum.
Remove and clean the plastic filter inside hose.
Remove the hose onto the pump, and check for blockage or obstruction here.
This should clear the fault
please leave feedback for my solution.
Thanks.

Dec 14, 2009 | Hotpoint Ultima WF865 Front Load Washer

1 Answer

Hi I have a hotpoint washing machine model wt761 and it has stopped working, it will not drain. The display is showing an error code F-05. Can you help me please.


You have a blockage not allowing the drum to empty.
Check for blockages via the pump filter and the hoses
F05 means blocked pressure switch
If it still won't work come back to me

Oct 25, 2009 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Hotpoint wt965 f04 error


F04 indicates that the pressure switch is jammed on empty,
check that the pump is working o/k, if it seems o/k and it drains o/k, then you have no alternative than to call an enginner
This really is your only option.
Plz rate my solution
Thanks.

Dec 18, 2008 | Hotpoint Ultima WD72 Front Load...

1 Answer

Not emptying


what that signals is the impellor on the end of the pump is jammed or loose. Check to make sure it is free.

Jun 15, 2008 | Hotpoint Ultima WD72 Front Load...

Not finding what you are looking for?
Hotpoint Aquarius WD640 Front Load Washer/Dryer Logo

1,892 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...