Question about Electric Light Switches & Dimmers

1 Answer

ELECTRIC DRYER WON'T START

MY ELECTRIC

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 21 Answers

Check the breaker first. if it is not off or tripped then the starter button could have gone out.

Posted on Dec 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My BSA A65 engine dies when I turn o0n the headlamp switch. Now the bike won't start and I have no lights working?


Sounds as if you have a short circuit in the headlamp circuit. While this could be anywhere, most likely a pinched wire somewhere you have removed and reinstalled some part. The seat? Replaced headlamp bulb? As to no longer starting, you may have blown a fuse due to the short.

Nov 14, 2014 | General Electric G.E. Arc Fault Breaker

1 Answer

750 bonecrusher garbage disposal motor half-way start after hitting reset but won,t run


Copy following link for troubleshoot resources, and replacement tips.
http://waterheatertimer.org/How-to-repair-and-install-Garbage-disposal.html

Make sure unit is getting at least 80% rated voltage.
115 x 80% = 92 volts

Mar 01, 2013 | Light Switches & Dimmers

1 Answer

My garbage disposal won't turn on, and i've felt down there and can't feel anything blocking it...what can i do now


Check circuit breaker.
Check red reset button on side of disposal and see if it's popped out. It's under sink, next to wire connection on disposal.
See if electric switch has gone bad. Listen if disposal makes humming sound. Humming means electric power is good.
Use vacuum cleaner hose instead of hand to check for stuff inside disposal
Use wood broomstick and see if cutter disk rotates freely.
If disk is stuck, wedge broomstick against side of sink opening until disk comes free, or use allan wrench on bottom of disposal.
If electric power to unit is good, and reset will not reset or reset is not tripped out, and if cutter disk rotates freely, then disposal has gone bad.
You can continue using sink as long as there is no leak that will damage cabinet underneath.
I wrote ex disposal replacement steps from my apartment maintenance days.
http://www.fixya.com/support/r7929008-replace_garbage_disposal

Aug 15, 2011 | Ace Hardware InSinkErator Badger 5, 1/2 HP...

1 Answer

How to adjust to daylight savings time?


The 2 silver stops with thumb screw are the stop & start indicators. Loosen thumb screws adjust start & stop times. Tighten.

Nov 03, 2009 | Electric Intermatic T171 24 HOURS 40 AMPS...

2 Answers

No power in the two bathroom electric outlets.


What do you mean protected, if they where ground fault they have a test button,or the breaker
can be a ground fault, but it is a lot cheaper to buy the outlets. Call someone that knows electric,
because you need to check to see which outlet has power coming from the breaker,because this one
is probably bad, which will not allow any power continue on to the next outlet. Just say you were
going to do this yourself , you need a tester to make sure power is coming to the outlet.

You could buy a ground fault outlet and a regular outlet, but you have to make sure that the ground fault
is wired from the breaker, the power from the breaker, then the wire that Leeds from the ground fault
to the other outlet will also be protected, one ground fault can protect two other outlets that are connected to it in what is called a series. Unless you have a multimeter to test what needs to be tested
you should ask someone that knows electric. If you have any more questions please post back as everyone is more than happy to help. I don't feel comfortable trying to explain to you how to replace
the outlets, it can be dangerous and I would not want you to get hurt just to save a few dollars.

Mar 25, 2009 | Light Switches & Dimmers

1 Answer

My snow thrower wont start


Change the spark plug being sure to set the spark plug gap as recommended in the owner's manual. Then clean or change the air filter. Finally use new high test gasoline. good luck.

Jan 12, 2009 | Mowtownusa Snow Thrower Starter Switch for...

Not finding what you are looking for?
Light Switches & Dimmers Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electric Light Switches & Dimmers Experts

Steve

Level 3 Expert

3287 Answers

Mike Carew

Level 3 Expert

958 Answers

Archaeology
Archaeology

Level 3 Expert

662 Answers

Are you an Electric Light Switch and Dimmer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...