Question about Audio & Video Receivers

Open Question

I have a Rotel RA-01 Amplifier which is now longer working due to it getting hot and blowing the power fuses. Replacement fuses last about 1 second when switched on before blowing again. Any ideas?

Posted by on

1 Suggested Answer

SOURCE: pioneer vsx-07tx-blows fuses immediately

put 20a fuse in.

Posted on Dec 29, 2007


Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does the fuse blow Instantly?


Link for the service manual: http://elektrotanya.com/pioneer_vsx-305_405.pdf/download.html On page 50 of the manual (36 of the pdf) it says for the "Sub woofer pre-out jack (Not available on the VSX-305 model) If you want to boost the low frequencies, connect to a subwoofer power amplifier" Your model will not drive a sub-woofer with out another amp. His sub may be a powered sub?

Aug 31, 2014 | Pioneer VSX-305 Receiver

1 Answer

SPEAKERS KEEP GOING OFF


I HAVE A ROTEL AMPLIFIER THAT WAS DOING THE SAME THING I TRIED TO CHANGE FUSES BUT THEY WERENT BLOWN THE I REALISED THAT IT HAD BEEN SITING UNUSED FOR A LOT OF TIME SO AFTER WORKING IT A COUPLE OF TIMES THE BROBLEM WAS FIXTED

Jun 12, 2014 | Yamaha RX-V375

1 Answer

I cannot get equal volume on both channels. It snaps crackles,


If it's an old type control then you can spray it with Servisol switch cleaner. You might have to take the top cover off to get better access.

May 27, 2013 | Rotel Ra-2030 Integrated Amplifier Review,...

1 Answer

To Mr. Hyde: you appear experienced with Bose 501 Series III speakers. I need to replace a burned out glass bulb fuse inside the right speaker, the fuse for the woofer I believe. I think that you said that...


Hello whit_hughes,

Just received your request for some information regarding Bose 501's......... Series III. Your looking for te manufacturers part # for the fuse which is in line with the woofer? The fuses used ON the Series III Crossovers (hard wired/soldered directly to crossover board/componants) have been Identified as BUSS #2494, 2amp, Quick-Blow Glass Tube Type Fuses. The fuse which is in-series with the woofer & the fuse which is in-series with the pair of tweeters are the same! In theory this means that the woofer is capable of twice the wattage of the tweeters due to the tweeters being wired in series with each other..... which in turn divides the power beween the two equaly. On the woofer circuit there is only the one speaker or voice coil obsorbing the power. The woofer circuit being wired in parallel with the tweeter circuit again splits the power between the two cuircuits..... so in an ideal situation the woofer sees 50% total input power while the tweeters each see 25% total input power;;;; totaling 100% total. The way Bose has fused them in the Series III's is such that each branch can obsorb a total of 2 amps before shutting down each indivigual branch. This can be adventageous..... should peak power be exceeded causing loss of full load abruptly, Amplifier Power Output Transistors usually blow..... however when only half of the full cuircuit shuts down due to peak power exeeding limits causing one fuse to open (blow) ... the actual impedance (resistance) of the speaker increases protecting the Amplifiers Output Transistors! Thats the reason for the 2 fuses. Each of them are identical. They are soldered into place.... via the wire which is attached to each end of the fuse. (Note; the fuse "kit" Bose is trying to sell you is an external in line fuse holder for each speaker {costing 1.29 each} & 2 fuses for each holder, One for now & One for Later aftr it blows {costing 1.00 each}..... costing Bose 6.58, neting Bose $13.42 Profit!!!! Keep in mind that this fuse WILL NOT FIX YOUR PROBLEM EITHER! DUE TO THE FUSE WHICH IS PRESENTLY BLOWN HAS NOT BEEN REPLACED!!!!! ) The one that has to be replaced is on the crossover... not between the Amplifier & the Speaker Enclosure. Tools required = 1 Long Big Straight Blade Screwdriver to pry off speaker grill, 1 Phyllips Screwdriver to remove screws seccuring woofer to encloser... be carefull not to damage/tear gasket, 1 pair side cutters to cut blown fuse out of crossover curcuit, 1 pair needle nose pliers to attach NEW fuse to crossover curcuit, 1 soldering Iron & a small piece of solder to re-solder fuses leads securly to crossover curcuit. ( replace gasket, woofer, screws, & speaker grill. ENJOY! Should additionaL informaton be required please let me know.... you'll have to leave me your e-mail address for pictures or drawings.... as I don't think they can be sent through this site. Hope this helps ya..... Its an EASY JOB...... you CAN DO IT! & will be glad you did when your done, they'll sound GREAT! ) GOOD LUCK!

Jun 22, 2011 | Audio & Video Receivers

1 Answer

Right speaker does not work on both A and B


Before doing anything else swap the speaker connections over to make sure that the problem is in the amp and not the speaker / speaker cable.
If that doesn't solve it then it is most likely an internal fuse blown on the amplifier circuit board - they are little tiny glass ones, obtainable from most tv repair shops, but it is important to get the right power rating. Also some of these fuses are 'quick blow' (go instantly there is a fault) others are 'slow' or 'time' blow - take a second or two before they actually blow - make sure you get the right one (timed usually have the letter T next to the power rating)

Mar 22, 2011 | Technics SA-DX930 Receiver

2 Answers

I have a "peavey ultra 410" guitar amplifier. it has been sitting in the garage for several years, and there is no power when plugged in. The amplifier is all tube (preamp and amp). My question is this; if...


Even though I don't have a schematic, if you have a VOM, (Volt-Ohm, Milli-Ammeter) we can start. Just because tubes are old doesn't mean they are used up. If a tube doesn't light up that would be a bad one, but they are in parallel off a winding of the power transformer. 1.) Check the on/off switch with the ohmmeter and the line cord for conductivity. 2.) Check the primary winding of the transformer for a low ohms reading. (less than ten ohms). 3.) Some where between the power switch and the pwr. trans. should be a fuse. After these three you should be able to put 120vac. to the unit and bring it back on. Get back with us, Dale

Aug 04, 2009 | Audio & Video Receivers

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68301 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...