Question about Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore Elite Elec Dryer Model # 110 62032100

Dryer will work through the cycle of drying clothes. After a few minutes with or without clothes in the dryer it will turn on an start beeping. You can press the cancel button and it will turn off. However a few minutes later it is back on beeping agin flashing a dry time of 56 or 36. It also just started to not turn on sometimes, but after unplugging the dryer it will work. Also it flashes clean the lint screen and it is clean. Is this a control panel circut board problem? Is this worth repairing or is it better to go out and buy an inexpensive dryer for 300 to 400 dollars?

DKT

Posted by on

  • fleabiters Feb 06, 2009

    dryers keeps beeping and flashing 36 minutes, it does this on its own even when it has not been in use for days. The only override seems to be to unplug once the cycle starts again it will finish then start beeping and flashing 36 minutes again.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Kenmore Ellite Dryer - Model 110.73952102 Type DDOT - NAT 1206006 - EH22

The Heat does not turn on! It spins and spins but no Heat? Any suggestions and how to fix intructions would be greatly appreciated. Thank you!

Posted on Nov 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore elite dryer,it's shutoff before it's time. like you set for 30 minute is off within 5 minute.


Try to run it in a timed cycle and see if it works longer. It could have a bad moisture sensor and thinks that the clothes are already dry. Prove it out and then replace it.

Sep 30, 2010 | Kenmore Dryers

1 Answer

Dry take hours to dry


need to check hi limit thermostat on element make sure it is not cycling to soon

Apr 13, 2010 | Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore Elec Dryer timer & Heat Element Failed


if you set timer on time dry it will count down but if you have it set on more or less it will not advance without heat,change out the heater and you will be fine

Nov 04, 2009 | Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore dryer beeps constantly


End of Cycle Signal
The End of Cycle Signal produces an audible sound when the
drying cycle is finished. Promptly removing clothes at the end of
the cycle reduces wrinkling.
@ H_GH
@ LOW
@ OFF
END of CYCLE S_GNAL
Press END of CYCLE SIGNAL to adjust the sound level or turn off
the signal.
NOTE: When WRINKLE GUARD _ is selected and the End of
Cycle Signal is on, a tone sounds every 5 minutes until the
clothes are removed, or WRINKLE GUARD _ ends.

Sep 15, 2009 | Dryers

2 Answers

2 to 3 cycles to fully dry clothes


if the clothes are warm after the cycle then you need to make sure the vent to the outside of the house is not plugged if they are not warm then it is in the heating circuit of the dryer wether it be the element or a fuse will have to be tested. to dry clothes it takes heat and air flow if you dont have one of the two they will not dry correctly

May 18, 2009 | Kenmore Elite Oasis 6808 Electric Dryer

2 Answers

Kenmore Elite dryer heats but does not dry


Make sure that your vent tube is not kinked or crushed behind the dryer and it all this is ok then you need to change your cycling thermostat. is it gas or electric

Mar 12, 2009 | Kenmore Dryers

1 Answer

Kenmore Elite HE3 Dryer clothes not dry after cycle


it sounds like a clog in vent.if yours vents up thru roof you may need to have a chimney sweep come out and sweep vent.check and make sure the vent hose is net kinked or full of lint.

Mar 06, 2009 | Kenmore Elite HE3 Steam 8674 Dryer

1 Answer

Dryer works for few minutes then stops


clothes can open the door if door latch is weak, causing door opening and stopping the cycle, or a bad automatic sensor

Feb 17, 2009 | Kenmore 62602 Electric Dryer

1 Answer

Dryer cuts off before clothes are dry.


Might be the thermal protector in the motor that is shutting down the dryer, if motor overheats this is what will happen. Make sure there is no lint build up around the motor, if not the motor is bad. does the dryer start right away after shutting off or do you have to wait? If you have to wait the motor is bad.

Jan 13, 2009 | Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore Elite HE4 Electric Dryer - heat but not drying


you have thermistor failure/ located inside machine reason for premature heat

Oct 07, 2008 | Kenmore Elite HE4 Electric Dryer

Not finding what you are looking for?
Kenmore Elite HE4 Electric Dryer Logo

Related Topics:

497 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...