Question about RCA P61960 61" Rear Projection Television

1 Answer

Starts running thru channels and inputs

Tv works fine for a while then starts running thru channels and inputs for awhile. Then works fine Then repeats same problem.
Unable to turn off and other controls do not work when running thru channels and inputs

Posted by on

  • diy_stuck Oct 14, 2008

    Good call!

    Thanks

  • Lo Burdine Jan 20, 2009

    I have the same model and my tv is doing the same thing. I would like to know the cost for gettint it repaired.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

The Micro switches are leaky. They are soldered on the control panel in the front. Either replace the panel or the switchs. You can test this by unsoldering all the switchs and leaving the IR Sensor. You can control the set by using the remote remote . If this help let me know.

Posted on Oct 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Digital tv tuner not displaying picture


. Try putting you tv set to channel 3 or 4. Try your tv in all modes. Check the back also to see if in the right spots with the wires. Check your channel scan status, try it on anntena and try it on cable, run channel scan on both. good luck. Try vcr wires if cable wires dont work. vcr wires are yellow red and white. Try another cable cord sometimes they get old. Try looking at your remote and setting it to tv.

Sep 02, 2012 | Panasonic PT-50LCX63 50" Rear Projection...

1 Answer

Have a hls 4676s and the tv turns on works fine then a clicking sound starts and the sound goes off. turn tv off, wait 20 min, turn back on and fine for awhile repeating problem


You Sr are experiencing the signs of a bad ballast. It's not able to keep up the voltage to light up the lamp. Therefore as a safety measure, it turns off.

Apr 21, 2010 | Samsung HLS4676S Television

1 Answer

Change from TV mode to AV mode for a Hitachi C28W4110SN


There should be buttons somewhere on the TV itself to switch input modes. Look around where the power button is located and see if there is a menu button you can access. Then use channel up/down and volume up/down to scroll thru modes to find input

Hope this helps
TankMurdock

Apr 27, 2009 | Hitachi 61SDX01B 61" Rear Projection...

1 Answer

Unable to view DVD on TV


Here is a solution buy a coax to RGB converter they run from $20- $30 at radioshack this will shore up that problem as it will use channel 3 as the input of choice.

Apr 23, 2009 | Projection Televisions

1 Answer

TV turns on with sound but blank black screen


This solution from troylove solved my problem. troylove11
Rank:wizard_s.gif Wiz
Rating: 85%, 1164 votes
This model is equipped with a self-diagnosis feature to help with diagnosis of shutdown problems. To activate this turn the unit on let it shutdown then press the input/device and menu buttons on the front panel simultaneously and hold them in for 5 seconds after 5 seconds the power LED on the front panel will blink a two digit sequence. This will be one set of blinks a short pause then another set of blinks, this will repeat 5 times. 1 - 2 = no error detected 2 - 1 = X-ray protect (high voltage or beam current) 2 - 2 = Short protect (short protect monitors low voltage supplies) 2 - 3 = Deflection protect (this could be loss of vertical or horizontal deflection) 2 - 4 = Vertical protect (usually loss of vertical from the source.

Jan 07, 2009 | Mitsubishi VS-50607 50" Rear Projection...

1 Answer

We have an LCD samsung Tv and a samsung dvd player with hard drive. We are unable to now go thru the source list and find HDM1 which was our dvd channel and get the dvd player to work, When you go on...


Samsung inputs are auto-detecting, meaning if nothing is plugged in you cannot get to that input. Double check you HDMI cable on both ends to make sure its plugged in. HDMI jacks are very weak and connections break very easily, don't wiggle excessively. I recommend using component video instead for a more reliable connection.

Dec 07, 2008 | Projection Televisions

1 Answer

TV screen goes blank but power stays on


Sounds like the CRTs are going into protective blanking due to the vertical output ic needing to be resolderd. Try resoldering the vertical IC that may possibly fix the issue.

Jun 15, 2008 | Mitsubishi WS-73713 73" Rear Projection...

1 Answer

Off Air?


The Scientific Atlanta box was a cable box and recieved CATV signals. The Direct TV box is satellite only. You might check if it has a built in ATSC tuner for off air digital signals. Direct TV in most locations offers the major networks in HD format.

Jan 04, 2008 | Sony Grand WEGA KF50WE610 50" Rear...

1 Answer

Missing cable channels


plug out the pwer for the tv and letit stand for awhile there after plug it in and see what it does ,if that does not fix the problem call in the tech the tv is having problem in the tuner circuit or the IF section good luck,

Apr 05, 2007 | Sony KP-44PX3 44" Rear Projection...

Not finding what you are looking for?
RCA P61960 61" Rear Projection Television Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

Are you a RCA Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...