Question about NetGear RangeMax Dual-Band Wireless-N Router with 4-Port Ethernet Switch

2 Answers

Configuration: Having configuration problems

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 78 Answers

DONT WORRY DEAR,
Go to the command prompt...
type in ipconfig hit Enter Key
It will Display your Ip address, Subnet Mask and the default Gateway.
Now, the router has to be configured using the Default Gateway.. eg 192.168.1.1
type this in the address bar of internet Explorer and do the configuration setting....
Ask you ISP for the uid and the password,

for more help try to check this blog-- www.primustel.blogspot.com
was i helpful enough??

Posted on Nov 17, 2008

Maybe you might want to clarify that question ?what configuration

Well try going to your router ip adress it might be in the manual and it usually starts like this http://192.XXX.X.X
SSID = Network name
WEP/WPA/WPA-2 PSK are encryption protocols use WPA-2PSK for better security * with this you need to enter a password

You need to setup your other wireless devices using windows wireless setup wizard or use the software on the cd (wireless device cd)

I hope i managed to answer your question?

Posted on Oct 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to ubiquiti rocket m2 Port Forwardin


having problem of configuration with my rocket m2

Jan 23, 2013 | Ubiquiti Rocket M2 MIMO 11N AP

1 Answer

I have a Motorola surfboard want to create wireless network


Should do it during set-up. More than likely you are having a problem because the modem comes pre-configured with wireless security enabled. Use the WPA-PSK code found on the label on the bottom of the router/modem or on the extra labels.

May 12, 2010 | Arris SURFboard SBG900 802.11g/b...

1 Answer

Cannot connect to the internet


hi, be sure you configure already your router so that it will automatically connect to internet...


regards

Mar 18, 2010 | Wireless Access Points

1 Answer

Configuring an alvarion router


well your asking a lot out of this. you need the software that came with it it tells you how to run it and ect... if you lost it look it up online for the software.

Jun 04, 2009 | Alvarion BreezeNET AP-10 PRO.11

1 Answer

Can not log in to senao 3220


There are multiple issues here, and vague reports.
The original poster's problem could be caused by any number of configuration errors. Without him reporting his configuration, it would be impossible to diagnose this problem.
The April poster reports a non-problem, in that his PC's indication that his LAN is active means only that the device at the other end of his ethernet cable is communicating properly with his PC, but says nothing about whether access to the internet past that point is active or not. He reports other valid problems, such as difficulty understanding and performing the configuration process, but again much more detail is necessary in order to pursue his issue.
The March poster reports a symptom that implies that he has a bad cable, POE, or main unit (assuming that his PC ethernet port is known good). Swapping components to identify the faulty one is indicated here. I realize that an average user may not have more than one of some of these components, but someone will have to do this to identify the issue.

Feb 14, 2009 | EnGenius EOC-3220 (EOC3220)

1 Answer

Connection


The setup page to configure Belkin routers is at http://192.168.2.1

If you have changed it, reset the modem to factory defaults by using a paper clip in the small reset hole.

Jul 04, 2008 | Belkin Wireless G (F5D7130) (F5D7130FR)...

3 Answers

192.168.1.1??????


Hi john - the address 192.168.1.1 is the default address of your router. Your pc that you're using for setup is supposed to be set to 192.168.1.10. with subnet mask 255.255.255.0 . Are you having problems getting in to your router? Do not enter anything for the default user and password. Let me know what problems your having. Thanks.

Jeff

May 17, 2008 | EnGenius EOC-3220 (EOC3220)

1 Answer

Process to configure wireless access points.


What exactly are you having trouble configuring, specifically?

Nov 23, 2007 | Linksys Wireless-G WGA54G 802.11g/b...

Not finding what you are looking for?
NetGear RangeMax Dual-Band Wireless-N Router with 4-Port Ethernet Switch Logo

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top NetGear Wireless Access Points Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Brett Duxbury
Brett Duxbury

Level 3 Expert

2733 Answers

Are you a NetGear Wireless Access Point Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...