My start menu has gone how do i get it back

Try resetting it to factory fresh.

1. Click the menu button and then click help .
2. From the Help menu choose Troubleshooting Information. ...
3. Click the Reset Firefox... button in the upper-right corner of the Troubleshooting Information page.
4. To continue, click Reset Firefox in the confirmation window that opens.

Good day!!!!


I need some clarification...

If the settings is gone then go to the TV mode..or the settings is gone and no picture?..or the settings is gone then the back light is gone..

Please reply to this tread to give you a specific solution..

Thanks for using fixya...

Hi,

You need to switch the TV to digital mode before you run the auto-program. Press the "DIGITAL/ANALOG" button on your remote before you run the scan. After switching to digital mode please complete the following steps to run the auto-program:

1. Press the "MENU" button on the remote
2. Press the right arrow ">" button on the remote once to highlight "CH" (looks like 3 boxes)
3. Press the "+" button (in the center of the arrow keys) to select.

You will now be in the "Digital Channels" menu. If you are in a menu called "Channel Setup", you are in the wrong mode. You should exit the menu, press the "DIGITAL/ANALOG" button on your remote and start again at step 1.

4. Press the down arrow on the remote to highlight "AUTO PROGRAM"
5. Press the "+" button (in the center of the arrow keys) to select.

The auto program will now run. This could take a while to complete but a progress bar is displayed so you can see how far it has gone.

If you can't get this to work or need further assistance, please post back.

Regards,
BElectric

Get a zenith universal remote with enter button, go to channel setup and it will apear cable- air, choose cable but press enter on the remote and it will start to program itself and let it finish, it will take like 10-15 min to scan

I got the error 51 once and it turned out the connector to the ink holder was loose so i put it in and error gone.If this not help you need clean the encoder strip.

To open Sidebar

•
Open Windows Sidebar by clicking the Start button , clicking All Programs, clicking Accessories, and then clicking Windows Sidebar.
To keep Sidebar visible at all times, you must set it so that other windows won't cover it. The Sidebar width is a fixed size.

To keep windows from covering Sidebar

Because of the space Sidebar requires, this option works best if you're using a large or wide-screen monitor or multiple monitors.
1.
Open Windows Sidebar properties by clicking the Start button , clicking Control Panel, clicking Appearance and Personalization, and then clicking Windows Sidebar Properties.
2.
Select the Sidebar is always on top of other windows check box.
3.
Click OK.

Ken, one of the buttons will be the menu button. eiather the first or the last.
If you up and down thru that menu, you should find a reset or auto reset.
Good luck

Please try to Turn the monitor off. Hold down the Menu button while the monitor is turned off, then press the Power button again to turn the monitor back on. This should unlock your OSD menu and remove that message from your screen. best regards

To reset the settings back to English:

1. Set the DM-20 to Voice mode using the blue switch on the back voice recorder.
2. Remove the DM-20 from Hold using the gray switch on the back of the voice recorder.
3. Press and hold the DISPLAY/MENU button on the front of the DM-20 for at least 3 seconds. The menu list is displayed.
4. Click the REWIND button six times to highlight the Format menu item.
5. Click the PLAY button to select the Format menu item. A message will be displayed with Cancel and Start options.
6. Click the REWIND button once to highlight Start.
7. Click the PLAY to select Start. A message stating that the data will be cleared will display briefly. Then a message asking if you are sure will be displayed.
8. Click the REWIND button once to highlight the Start menu item to continue with the format.
9. Click the PLAY select the Start menu item and begin the format. The format progress bar will appear. When it is complete the menu items will be in the English language.