Question about Gigabyte 7VM400M-RZ (GA-7VM400M-RZ) Motherboard

2 Answers

Bios setup error

I have found an error in my computer. When I am switching on power button of my computer following messege is appearing :-

"Auto detecting USB mass storage devices ...
00 USB mass storage devices found and configured.

USB device over current status ditected !!
System will shutdown after 15 seconds."

After showing the above message the computer shutting down after 15 seconds. Even I cannot enter in BIOS setup.

I have checked all the hardware & USB port but the result is same.

If anybody help me i will very gratefull to him.
I have the same problem but i have a PK5-VM mother boared and when i start it it says the same thing but evn though i have removed all the USB devices it still doesn't work please help me

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Kesin çözüm.
Usb girişlerinden birinde bi yıpranma var ve içinde bulunan 4 iğneden biri şaseye temas ediyor. Yani zor kullanılmış bu noktaya.
Hayırlı günler.

Murat Canıtez
murat_canitez_1@hotmail.com

Posted on Dec 14, 2008

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 3 Answers

Check your c-mose battery when power cable is unplugged the battery remove and after few seconds battery fix them and connect power cable then on the computer

Posted on Oct 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to access the menu


Know what the ->enter BIOS Setup key is?

It's on the bottom of the computer manufacturer logo screen.

Got it?

Now press the CTRL and ALT and DELete keys at the same time.
Restarts the computer.

JUST AS SOON AS IT STARTS, start tapping on the enter BIOS Setup key.
Tap in 2 seconds intervals.

If you hear beeps ignore it. These are Stuck Key Error Code beeps, and it is you that is making them.

Still No?
Turn the computer off by holding the Power On button in, for 10 seconds.
WAIT 20 seconds, then press the Power On button.

AS SOON AS YOU PRESS the Power On button, start tapping on the enter BIOS Setup key. The rest is above.

Regards,
joecoolsvette

[The time period to enter BIOS Setup goes by F-A-S-T!
As soon as you see the computer manufacturer 'splash screen', (Logo screen), it may be TOO late. The above method makes sure you get in BIOS Setup ]

Nov 21, 2012 | Motherboards

1 Answer

Mainboard GA-G31-ES2C Warning: Backup BIOS checksum error BIOS Auto-Recovering...


If you have reset the CMOS memory you need to go into the BIOS setup screen and reconfigure the BIOS. To do that you need to press a key while the computer is booting. Usually F2 but can be other keys. It should tell you on the bottom of the first screen which key to press to enter BIOS setup.
If you don't know the settings the should be one for optimal defaults - use that one. You will also need to reset the time and date.
Save, Exit and re-boot and everything should then work.
During the boot process you will see on the screen to press delete to enter setup

Jul 23, 2011 | Gigabyte GA-G31M-ES2L Motherboard

1 Answer

System shutdown in 15 seconds


Shut the power down to the computer all the power and pull the power cord out, remove all usb devices except the mouse and keyboard, Turn the unit back on and see if this fixes the problem, if it doesn't then you will have to go into the computer and clear the c-mos this will allow you to get into the bios screen from there you can set up the computer again. Check you manual for the instructions on bios reset, most times it is just pins 2+3 that need to have a jumper installed to reset it. READ THE MANUAL PINS 2+3 APPEAR ON MANY THINGS ON THE CIRCUIT BOARD

May 31, 2010 | ASUS P5PE-VM Motherboard

2 Answers

P4S800D.ROM not found


check the the bios battery, it should be 3volt not less,and press dell to in the bios page setup set and set everything you need to do.and don't forget to save it,. good luck

May 10, 2009 | ASUS P4S800D Motherboard

1 Answer

Bios Problem


When I Power On The PC And I Hit Del To Inside The Bios To Slow And Every

Oct 23, 2008 | Motherboards

4 Answers

System shutdown in 15 seconds


hi, pl check for viruses, scan the system, and go to cmd prompt and issue this commnd at c:\ shudown -a and press enter to disable reboot and scan the system and check any hardware issue.

Aug 12, 2008 | ASUS P5PE-VM Motherboard

1 Answer

Bios setup error


Unplug ALL Usb devices, that includes printers, cameras, pen drives, i.e. anything that plugs into a USB connector. Then try rebooting your computer. I bet your problem will no longer exist, but if it does, then you need to suspect a faulty USB connector on the motherboard or USB chipset located on the motherboard. Once the computer is booting normally without USB devices hooked up, you can start installing ONE Usb device at a time, until you find your defective USB device. The USB device drivers will need to be installed and computer rebooted at least once between the various devices. Not doing so will lead to confusion as to which USB device is causing your high current problem. It is also possible athough a bit unlikely that this procedure will cure your situation for the time being but look out for it in the future because it could be an early sign that one of your USB devices is going bad.

Aug 11, 2008 | ASUS P5PE-VM Motherboard

1 Answer

SYSTEM ERROR


1) if you have nothing in a USB port you will need to set bios
Try removing M/board battery for 2 to 3 hours some people say less then replace it most times it should set BIOS back to default
also check setup of hard disks master slave etc

Last resort with 15 seconds you should be able to see
press ?? key to access BIOS next boot keep pressing key see if that works

Aug 10, 2008 | ASUS M2N-MX Motherboard

3 Answers

P4PE Motherboard system hangs on 2 memory banks


you need to check in your bios settings for the amt of physical memory setting. alsoexamin the board for defect. if all that is good then follow the following instructions

1.)Unplug computer
2.)remove memory
3.)switch jp1 to clear ( the jumpewr that clears the bios is called jp1 its located close to the battery and it has 3 pins and 1 jmper) the pin set will be on 1 and 2 , simply set it to 2 and 3)
4.) Hit the power button 5 times to clear all remains of eletricity
5.) REPLACE JUMPER TO 1 AND 2
6.) replace memory
7.) boot up system
8.) on the main boot screel it should say no bios settings enter setup
9.) enter setup and load optimal defaults
10.) save and exit

Dec 31, 2007 | ASUS P4PE-X Motherboard

1 Answer

Monitor will not wake up when pc is turned on


How do I disable the power, sleep, and/or wake buttons in Windows? Answer: Disable the computer's ACPI feature If you wish to disable all three of these buttons, you can disable the computer's ACPI feature in BIOS / CMOS. Additional information about how to enter the BIOS / CMOS setup can be found on document CH000192. Once in BIOS / CMOS setup, you can disable ACPI in the power category. The location of this option is almost always different between all BIOS manufacturers and versions of BIOS.
Change the power option within Windows Microsoft Windows XP users By default, Microsoft Windows XP will prompt you what to do when the power button is pressed on the keyboard. If you wish to change this setting, follow the below steps.
  1. Click Start / Settings / Open the Control panel
  2. Within the Control Panel click Power Options
  3. In the Power Options Properties window, click the Advanced tab.
  4. Under Power buttons, click the down arrow under "When I press the power button on my computer" and/or "When I press the sleep button on my computer" and select the action you wish to perform when pressing the key.
Microsoft Windows 2000 users Unfortunately, Windows 2000 does not have all the features Windows XP does. However, you can change the power button or other buttons to perform a different function. For example, changing the power button to suspend instead of power. To do this, follow the below steps.
  1. Click Start / Settings / Open the Control panel
  2. Within the Control Panel, click Power Options
  3. In the Power Options Properties window, click the Advanced tab.
  4. Under Power buttons, click the down arrow under "When I press the power button on my computer" and/or "When I press the sleep button on my computer" and select the action you wish to perform when pressing the key.
Good Luck, Please dont for get to Vote, Thank You.

Dec 23, 2007 | Mercury P4VM800M7 Motherboard

Not finding what you are looking for?
Gigabyte 7VM400M-RZ (GA-7VM400M-RZ) Motherboard Logo

Related Topics:

278 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gigabyte Motherboards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Tony

Level 3 Expert

2598 Answers

Are you a Gigabyte Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...