Fisher&Paukel washer My washing machine filled with water and then stopped mid cycle and it was beeping. I tried the power button the washing machine and it would not turn off the washing machine, it just keeps beeping and the lights flashing. I have now taken out the clothes and removed the water that was in the machine and pushing the power button but it still wouldn't work. I have turned it off at the power point but it still will not work just beeps and nothing else.

Question edited for full maker name. This site does not do well with abbreviations.
Question moved to maker category.

It may be a failed control board, but a few things to try first.

Why Is My Fisher And Paykel Washing Machine Not Starting?

JustAnswer https://www.justanswer.com > Appliance Repair
Jan 30, 2009 - 1.With the machine off: Press and hold the WASH TEMP DOWN button and then the POWER button until the machine gives 2 short beeps and lights up.
1 answer · Top answer: Unfortunately yes. The parts only come from Fisher and Paykel and the board....

Troubleshooting

Fisher & Paykel https://producthelp.fisherpaykel.com > QuickSmart
Jul 6, 2017
Problem Possible Causes What to do Washer not turning on. Household power supply not working. Try plugging in anoth... Touching does not start the fill. Washer door not closed properly. Open and reclose door. Touching does not start the fill. Delay start maybe set. Refer to 'Wash cycle... View 47 more rows

Check the wiring harness, connections, contacts, etc. Look for some corrosion and loose connections. Also, check the water inlet for anything that may cause a reduction in water flow.

You need to supply brand and model numbers in the question itself when posting.


https://www.ifixit.com/Answers/View/116311/Why+does+my+washer+stop+half+way+through+cycle

https://diy.stackexchange.com/questions/21181/what-could-cause-my-washing-machine-to-stop-before-the-rinse-cycle

http://www.whitegoodshelp.co.uk/washing-machine-sticks-stops-mid-cycle/

http://appliances.wonderhowto.com/how-to/fix-your-front-load-washer-if-stops-mid-cycle-381047/

see this causes and fix it. God bless you
Lid Switch Assembly If the washer stops mid cycle the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design
Door Lock Motor and Switch Assembly If the washer stops mid cycle the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.
Water Inlet Valve If the washer stops mid cycle the water inlet valve cold water side may have failed. Most washers have a cold water rinse and so if they can't fill with cold water they just sit indefinitely waiting for the cold water to enter. If there is cold water to the water inlet valve and the cold water works in other parts of the cycle - or to make warm water - the valve is not the problem.

Main Control Board If the washer stops mid-cycle the main control board might be defective. This is not common. Check other causes first such as the lid or door switch and other components.

Timer If the washer stops mid cycle the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.

A failed inlet valve is not uncommon in F&P machines. The hot valve is different to the cold one, so don't exchange them. Not a big job for a tech to do in-laundry. Good luck....Nomess

try it on rinse cycle if goes ok then the hot water valve is faulty

hi
if the water is coming in when the machine is off then you have a faulty water valve and you need to start thereand solve that problem first
cheers grantsreps

CHECK DRAIN PUMP AND DRAIN HOSE FOR RESTRICTION

I can help with this. I work on the units they make. If you can email me @ [email protected] I will guide you through

you probably have a foreign object in the pump impellor - the favourite is bits of bra wire