Question about Sony KP-65WS500 65" Rear Projection Television

2 Answers

Kp65ws510 I have the exact same issue with my kp65ws510. My screen looks exactly as deformed as yours. It has the techs at my local TV shop stumped. They have been working on it for almost a month now. Replaced the ICs twice, all the pico fuses, and the HV wires... still not fixed. Were you able to resolve the issue?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 62 Answers

If convergence ICs are changed and pico fuses are changed, if the colors are still bad, check the resistors connected to STKs. Make sure you check there values with a good DMM. But if all there are good, power regulators ICs are good. The stdby power supply is controlled through D board and if the set is not comming on and the light is blinking its most likely the d board. all caps need to be checked with a good ESR meter. Hopefully you are able to resolve the issue. More specific diagnostics can be done using the service manual flow charts. If you dont have one download it from tech support on fixya site. Also check out www.fixurtvs.com. for FAQs.

Posted on Mar 25, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

No I have not resolved the issue yet. I had them test my D-Board again and they say it is fine. I was going to check the fuses next but you say that wasn't the problem with yours. I'm not sure what to do now..

Posted on Oct 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

47led55sa half the screen is black


Hello Kathy, now since i dont have a picture of the screen i cannot tell exactly what is wrong, but if i had to take a well educated guess it would be that one of the wired that feed into the screen is damaged or faulty . Take it to your local tech shop and they can fix this problem easily, though rates differ from place to place i would give a rough assumtion of $25-$30 for a proper fix. Hope this helped ;)

Oct 11, 2012 | Proscan 123882 Power Supply

2 Answers

I am looking for a general electric power cord it's 2002 model


The part number for this is: RCA #260519, but it is listed as no longer available. Your best bet is to call around to a few local repair shops looking for either a new old stock (NOS) one or a used one.

Dan

Dec 29, 2010 | GE 24GP653 24" TV

2 Answers

Horizontal lines are at the top of the screen (First 3-4 inches) rest of the screen looks fine


This seems to be a fault in the vertical blanking circuit. It's very common to have open or out of value electrolytic caps that make this problem.
I could guide you in finding this cap if I had the schematic for this TV, but I don't.

Dec 10, 2010 | Panasonic CT-27SL15 27" TV

1 Answer

I have a sony bravia flat screen tv. Often i hear a "pop up" sound from back of tv. What could cause this?


I quite certain that this is the Back Light Lamp Ballast power supply that may be causing this pop. If it's still under warranty. Best to call the local Sony Service shop and see if they can look at this to alleviate future major issues.
Blessings always,
A/V Media Tech Guy

Dec 03, 2009 | Televison & Video

1 Answer

My blackberry was unlocked however has gone to the reset screen a few times brought it to a tech guy after using it for a month the screen went blank there is still light in the phone but no sign of...


Try to reinstall your blackberry software since unlocked blackberry storm 9500 software usually has previous network configuration. But to make sure what exactly your problem you can bring your phone at local mobile repair shop and asking them to check your phone.

Nov 25, 2009 | RIM Research In Motion Blackberry Storm...

2 Answers

Black line in middle of 42'' plasma screen


It could be one of buffer was defective. Get it repair does not cost so much $$$.

Aug 18, 2009 | Televison & Video

1 Answer

Mitsubishi vs-4552A


Call your local TV shops and ask if they have any 45 or 50" screens in the bone pile you could purchase. You should come up with something for a reasonable price $35 to $50 in good to excellent condition. You can cut down the screen to fit if you cant get the exact size. Good luck!

Feb 22, 2008 | Mitsubishi VS-45607 45" Rear Projection...

1 Answer

Center toggle not working all directions TRU 9485-2


I've taken a look at the uniden australia site and it does not offer to buy or order pieces. Mostly likely, they'll ask to send it to a 'specialist'.

Ebay is always an option, if you know the exact membrane your looking for. Or find a local specialist shop, it should be cheaper than sending it in.

Thats all I can offer. Hope it helps.

Jan 01, 2008 | Uniden Cordless Phone

1 Answer

Sylvania 20" lcd screen problem


Your lcd screen is bad. Try to buy a TV on eBay with a good screen but won't turn on or some other problem. I have one just like it.
Bill

Sep 03, 2007 | Sylvania 6620LDG 20 in. EDTV-Ready LCD...

3 Answers

Picture looks 3d


It is hard to see, but it looks like your red color has shifted to the right. In most projection sets there are 2 large convergence IC's which put the 3 colors exactly where they are supposed to be on the screen. When one color is way off, giving the 3D effect, and you are unable to line the colors up using the convergence menu, it means that one of the convergence IC's has burned out. This is one of the most common failures in standard projection sets. The burned out IC should be replaced and the convergence circuits realigned by a qualified tech familiar with projection sets.

Aug 20, 2007 | Sony KP-43T70 43" Rear Projection...

Not finding what you are looking for?
Sony KP-65WS500 65" Rear Projection Television Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

kakima

Level 3 Expert

100387 Answers

The Knight
The Knight

Level 3 Expert

71172 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...