Question about Gmc Dodge Ford Reverse Back-up Sensor Alarm Kit

5 Answers

Free programming instructions for Prestige remote

I need to program a Prestige transmitter for my car alarm.  Where can I find free instructions?

Posted by on

  • 3 more comments 
  • Anonymous Dec 12, 2008

    can someone tell me why,when I start my truck after pressing the remote,it starts up,,and headlights continue to flash,,is this normal??

  • lmbond7 Dec 15, 2008

    I have the Audiovox APS 686 and trying to remote start and cannot. I have a red toggle switch located on the drivers dash. WHihc buttons do I press to start the car?

  • callejas Jan 29, 2009

    how to programming factory keyless remote for 1996 town coutry

  • Anonymous Mar 15, 2014

    prestige alarm does not respond to remote

  • Anonymous Mar 19, 2014

    car does not start with remote transmitter beeps like it should then flashes inhibit any thoughts , i tried to realign the receiver that didn't change anything.

×

5 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

YOU can call prestige tech support at 1800 225 5074.. or just put the key in the ignition turn the key all the way to the right without starting the car then flip the vallet switch usually located at the bottom of the dash drivers side, flip the switch on and off three times, you will hear a chirp then you should press the first button on the remote for 2 seconds then flip the swith on and off one more time , then press the second button the remote for 2 seconds then flip the switch again on and off one more time then press the 3rd button on the remote for 2 seconds... After which... remove the key from the ignition and your done... Try the remote to see if it works the way it should if not do it all over again..

MSB....

Posted on Oct 22, 2008

  • karr550 Mar 28, 2011

    yes it works d way it should.
    thanks

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have a 1997 4 runner  and 2000 gmc with prestige remote starter & alarm need to get new remote program.

Posted on Dec 06, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

I have a Avital alarm system that my mechanic disconnected but does not know how to re-install it. How do I re-install this alarm

Posted on Feb 08, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 1998 form mustang cobra ,lost my original control brend prestige model aps95bt3 ,trying to program one i buy, the same model cant get it to work,can any budy help.need intructions.thanks

Posted on Jan 13, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a prestige remote car starter. Batteries died in my remote so when I got it apart a metal piece that kind of looks like a cross popped off & I don't know from where & I can't figure out how to get the batteries back in. Please help

Posted on Jan 06, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How can I program my remote?


Remote for ? door unlock / lock , remote start , garage door opener .
If the door lock / unlock , panic alarm ,remote start . You can't dealer only . Need a factory scan tool .
Transmitter Programming
Important: Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. The order in which the transmitters are programmed is important. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. Use care to program the transmitters correctly.
The scan tool must stay connected until all of the transmitters are programmed.

Invalidate All
This procedure will erase all keyless entry transmitters from memory.
Install a scan tool.
Turn ON the ignition with the engine OFF.
With the scan tool, select Body.
Select Remote Control Door Lock Receiver (RCDLR).
Select Module Setup.
Select Program Key Fobs.
Select Invalidate All Fobs.
Follow the scan tool on screen instructions.
Transmitter Slot Programming
Transmitter slot programming allows a single transmitter to be programmed into a specific slot without affecting any of the other programmed transmitters. By using slot programming, the transmitter originally programmed to a specific slot is erased and the new transmitter learned in its placed.
Install a scan tool.
Turn ON the ignition with the engine OFF.
With the scan tool, select Body.
Select Remote Control Door Lock Receiver (RCDLR).
Select Module Setup.
Select Program Key Fobs.
Select the key fob desired to be programmed.
Follow the scan tool on screen instructions.
Remove the scan tool.
Exit the vehicle. Operate all functions on transmitters to verify correct system operation.

Jun 05, 2015 | 2007 Buick LaCrosse CXL Sedan

Tip

How to program Chrysler Remote Transmitter


A Chrysler Transponder Key once programmed into a one car cannot be programmed to work any other car.

The transponder code identification is learned by the Sentry Key Immobilizer Module during programming. The Sentry Key Immobilizer Module sends the "Secret Code" to the transponder key and is retained by the transponder key during programming. After programming of the transponder key identification to the Sentry Key Immobilizer Module and the Secret Code is exchanged, the Sentry Key Immobilizer Module will ask for the transponder identification and the Secret Code every time the key is turned to ON or START.



No Emergency "Start" procedures for Chrysler vehicles.



Chrysler Key Operation and Programming



Model: 300 Year: 2005 - 2008

Model: 300C Year: 2005 - 2007



Remote alarm / central locking



System Operation



  • Pressing key LOCK button activates alarm and central locking.


  • Pressing key UNLOCK button once deactivates alarm system and unlocks driver's door.


  • Pressing key UNLOCK button twice within 5 seconds deactivates alarm system and unlocks all doors and trunk.


  • Pressing trunk lid button twice opens trunk lid.


  • System will automatically lock all doors when vehicle is driven above 15 mph.


  • Additional functions can be set to respond to the transmitter.


Programming



When



  • Key transmitter added or replaced.


How



  • Key transmitter is programmed during immobilizer programming procedure.


Immobilizer

System Operation



  • Switch ignition ON.


  • Immobilizer warning lamp illuminates for approximately 3 seconds.


Programming



When



  • Keys added or replaced.


How:



NOTE: Two programmed key transmitters must be available for the following procedure to operate. If none available key transmitters can only be programmed using diagnostic equipment.



  • Insert first programmed key into ignition switch.


  • Switch ignition ON for at least 3 seconds but no longer than 15 seconds.


  • Turn ignition OFF and remove key.


  • Withing 15 seconds insert second programmed key into ignition switch and turn ignition ON.


  • After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will flash.


  • Turn ignition OFF and remove second programmed key.


  • Within 60 seconds insert non programmed key into ignition switch and turn ignition ON.


  • After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will illuminate for 3 seconds.


  • Switch ignition OFF.


  • Remove Key.


Check operation of programmed key transmitter.

Repeat procedure for additional key transmitters if required.





Model: 300M Year: 1999 - 2003

Model: Concorde Year: 1998 - 2003

Model: LHS Year: 1998 - 2001

Model: PT Cruiser Year: 2000 - 2005





Remote alarm / central locking



System Operation



  • System will automatically lock all doors when vehicle is driven above 15 mph.


  • Pressing remote transmitter UNLOCK button once deactivates alarm system and unlocks driver's door only.


  • Pressing remote transmitter UNLOCK button twice within 5 seconds deactivates alarm system and unlocks all doors.


  • Alarm / Central locking functions can be altered using remote transmitter.


Programming

When



  • Remote transmitter added or replaced.


How:

NOTE: One programmed Remote transmitters must be available for the following procedure to operate.



  • Obtain all remote transmitters.


NOTE: Any existing remote transmitters not used during programming will become inoperative.



  • Switch ignition ON.


Using a programmed remote transmitter proceed as follows.



  • Press and hold remote transmitter UNLOCK button.


  • After holding the UNLOCK button for at least 4 seconds but no longer than 10 seconds, press remote transmitterPANIC button for at least 1 second and release both buttons.


  • Ensure acoustic signal is emitted indicating programming mode active.


  • Within 30 seconds carry out the following procedure for each remote transmitter (including previously programmed remote remote transmitter)


  • Press any button of each remote transmitter to be programmed.


  • Ensure acoustic signal is emitted after each remote transmitter operation.


  • Programming must be completed within 30 seconds.


  • Switch ignition OFF or wait 32 seconds to exit programming mode.


Ensure final acoustic signal is emitted.

Replacement remote transmitters can also be programmed using diagnostic equipment.



Immobilizer



System Operation



  • System arms after switching ignition OFF.


  • Switch ignition ON.


  • Immobilizer warning lamp illuminates for approximately 3 seconds.


Programming



When



  • Keys added or replaced.


How

NOTE:Two programmed key transmitters must be available for the following procedure to operate.



  • Obtain all keys.


  • Using first programmed key turn ignition switch ON and wait 3 seconds, return to OFF position and remove key.


NOTE: First and second programmed key operations MUST be performed within 15 seconds.



  • Insert second programmed key and switch ignition ON.


  • Wait approximately 10 seconds.


  • Ensure immobilizer warning lamp begins to flash and an acoustic signal is emitted.


  • Switch ignition OFF and remove key.


  • Within 50 seconds, insert new key and switch ignition ON.


  • Wait approximately 10 seconds.


  • Ensure acoustic signal is emitted and immobilizer warning lamp remains illuminated for 3 secondsindicating programming completed.


For each additional key repeat procedure starting from the beginning.

Replacement keys can also be programmed using diagnostic equipment.



Automotive and Commercial Locksmith Chrysler Remote Control Programming...

on Mar 26, 2015 | Televison & Video

Tip

Dei viper python valet hornet boa transmitter programming help


DEI REMOTE PROGRAMMING INSTRUCTIONS
Need a DEI Remote Replacement Now? Try our all New Remote Quick-Find
Not sure what type of Replacement Remote you need?
In order to enter Learn Routine, the Valet/Program push button must be plugged
into the main brain's Blue 2 Pin Port (Look for a small black push button located under
the drivers dash or drivers kick panel somewhere). If you do not have the Valet/Program switch, you may order it at www.lesscoelectronics.com or www.lesscosales.com

1)
Open a door and make sure the dome light is on.

2)
Turn the ignition on to the RUN position or you may also start car.

3)
Within 15 seconds press and release the Valet/Program push button
to select the channel you wish to program. For example, press and release
once for channel 1 (arm/disarm channel).
For Channel 2, press and release twice (trunk release).
For Channel 3, press and release three times (remote start).
(Some DEI systems require different programming for different channels. You
can get specific installation manuals with remote programming instruction)

Press and hold the Valet/Program push button once more. You should get a
confirmation chirp/horn-honk or a flashing LED light (If installed).
If you do not get a chirp/horn-honk the alarm may have a jumper in
the alarm that has the programming feature turned OFF (disabled).

4)
Once the alarm chirps/horn-honks keep holding the Valet/Program push button.

5)
Press the button on the transmitter that you would like to control the selected receiver
channel. A chirp/horn-honk will confirm that the code has been learned. If programming
more than one transmitter repeat step 5. Old transmitter codes will be dropped only
if programming 4 new transmitters.

6)
Once the code(s) are learned, the Valet/Program push button can be released.

Learn Routine will be Exited if:

Ignition is turned off
Door is closed
Valet/Program push button is pressed too many times
More than 15 seconds elapses between steps
One long chirp/horn-honk indicates that Learn Routine has been exited.

on Jul 29, 2010 | Car Audio & Video

1 Answer

Code alarm protx6 fob programing


I would either go to the website for the manufacturer of the keyfob and search the troubleshooting section or get the company phone number and call them and get instructions for the programming codes. good luck.

Apr 16, 2014 | Audiovox Prestige Code Alarm Remote Alarm...

1 Answer

Set up the car remote


A 7701P is a remote transmitter. It is not an alarm. You must know the alarm's model because different models have various ways of programming transmitters. In other words, you do not program the 7701P. The frequency is already fixed. You must program your security system to teach it that transmitter's code. Look up the manual for your security system. Instructions will be there. This typically involves turning the ignition on/off a specific number of times and pressing a valet/programming button (or switch) a certain number of times and then pressing a button on the transmitter.

Jan 31, 2013 | 990 And 950 Responder SST Remote - 7701P

1 Answer

How to use?


The APS95BT3 is listed as the replacement remote for the Audiovox Prestige APS55LR.

A copy of the owner's manual can be obtained from the following link:
APS55LR Owner's Manual

The remote programming manual can be downloaded from the following link:
Remote Programming Manual

Dec 08, 2011 | Car APS95BT3 Transmitter with 3 Button...

1 Answer

I have a Prestige APS-20B 3 Button Vehicle Alarm System installed in January 2005 in my 2005 Toyota Rav4 Plus. The Dealer was High River Toyota In High River Alberta Canada. both of my key chain...


You can purchase these remotes online and program them yourself. If you have difficulty programming the remotes come back to FIXYA for instructions. The remotes also should have a phone number on the back for ordering.

May 05, 2011 | APS20B Prestige Keyless Remote Alarm

1 Answer

NEED TO KNOW HOW TO RESET A PRESTIGE ELVATCE CAR ALARM


REPRIORITIZING A TRANSMITTER’S PROGRAMMING:
To reprogram a receiver channel with a different transmitter button once a code has been stored, there will be two options:
  1. Enter the transmitter program mode of the receiver channel to be reprogrammed. Using any unused button or combination of buttons, push out the stored code by pressing the unused button until a long chirp is heard, then repeat 3 additional times. After this, you can add any desired unused transmitter button. This action erases only that particular receiver channel, all other codes will remain stored.
  2. Enter the transmitter program mode. Using any transmitter button press and hold until a long chirp is heard. If a single chirp or multiple chirps, (up to 7 chirps), are heard, the unit is indicating that the transmitter has already been programmed elsewhere in the receiver. Release the transmitter button and within 5 seconds press and hold until a long chirp is heard. This action forces the unit to erase all stored codes of that transmitter.
The unit then exits the program mode the siren emits the program mode exit chirp pattern. All transmitter buttons for that transmitter must now be reprogrammed. Any other transmitter stored in the unit’s memory still remain operational. If the button is released and not pressed again within the 5 second period, no change in programming has been made to the receiver channel. The programmer can move onto a different channel or erase the transmitter codes as described in 1 above.
Regards, Martin @ http://www.lesscoelectronics.com

Sep 21, 2009 | APS20B Prestige Keyless Remote Alarm

1 Answer

Transmitter no signal


check you setting or rest and start programming over

Jul 01, 2009 | Vehicle Parts & Accessories

2 Answers

Can you give me the instructions for programming the remote for a 1999 Jaguar XJ8. Thanks! Alan Broyles


  1. Hold headlight flasher back.
  2. Turn ignition key to position 1.
  3. Flash headlights 4 times. Alarm will enter programming mode. This will be confirmed by "beeps" from the alarm and flashing led on gearshift. Program each transmitter (up to 5) by pressing the lock or unlock button on the each transmitter once. The alarm will "honk" when you press the transmitter button. The alarm must honk 5 times to complete the programming. Therefore, if you are only programming one transmitter you should operate the transmitter 5 times. If you are programming two transmitters you will operate one transmitter twice, and three times on the other. For five transmitters you will operate each transmitter once.

Mar 12, 2009 | 1998 Jaguar XJ8L

Not finding what you are looking for?
Gmc Dodge Ford Reverse Back-up Sensor Alarm Kit Logo

18,370 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Vehicle Parts & Accessories Experts

Randy Ohler

Level 3 Expert

14585 Answers

Iron
Iron

Level 3 Expert

3018 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Toyota Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...