Question about VCRs

1 Answer

Taping I can't figure out how to tape a tv show on the vcr mode, for instsnce how do I know what channel to tape(they don't have anything relating to that. Also where do I connect my cable (shaw digital) to the vcr there is no cable port.

Posted by on

  • stargal Oct 15, 2008

    Thank you--- now I don't have to take them back. Love this web site

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 70 Answers

If there is no coaxial cable input on VCR, then it should work by RCA cables. Which is the Yellow , red/white cables. On the back of the VCR. Take a set of RCA cables Yellow for video, red/white for audio to the VCR output.Then do the same to the Television input. Next use the television remote to turn the TV to Video input this will allow you to view what's playing on VCR. Then take another set of RCA cables and reverse the first setup. Attached Cables to VCR input and cables to TV Output. This will allow you record what's on television. Now make sure the cable is screwed to coaxial cable input on television. This will able you to access cable programming on television, view vhs tapes, and record programming directly from television.Good Luck

Posted on Oct 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

VCR won't record, just ejects tape


You have not mentioned the make and model number of the vcr. Any way the problem is due to end sensor or related circuit. End sensors are photo diods which you can check the shorting with a multy meter.

Jan 13, 2013 | Emerson VCRs

1 Answer

Does ur vcr have to be on a certen chanel for it to show a tape? If so..witch?


No the vcr does not have to be on a certain channel to view a tape. The important thing is that the tv is on the correct input that the vcr is connected to. In some configurations the tv has to be on channel 3 or 4 but not the vcr.

Jul 06, 2011 | VCRs

1 Answer

My jvc HR D170 ES vcr used to work fine when suddenly the picture ( snow ) is very bad but sound is ok ...tried to retune to my tv ...tried changing the rf at back ...tried tuning to my other tv and...


The vcr is fine. buy a cleaning tape. people say dry cleaner tapes wear out the heads, but it fixed my problem when my vcr only showed snow. but try a wet tape first. follow the instructions that came with the tape and run it a few times.

Jun 26, 2010 | VCRs

1 Answer

Sharp VC-A582 I need a little help adjusting the tracking on my VCR, model Sharp VC-A582. I just acquired this unit and did successfully watch one tape for hours, then must have touch a wrong button by...


I couldn't find anything on your VCR either. But from personal experience I know that a lot of manufacturers use the channel up/down buttons on the face of the VCR as tracking controls while a tape is running.

My suggestion is to start a tape and then press the channel up or down button on the frnt of the VCR for a few seconds and see if it adjusts the tracking.

Hope this helps you out.

Oct 03, 2009 | VCRs

1 Answer

Had dish network update - can't view vcr tapes


the output of the vcr...
what is it physically wired to?

Dec 04, 2008 | Sanyo VWM-950 VHS VCR

1 Answer

Recording on a Panasonic VCR


This problem is undoubtably dirty or worn video heads. Try using a good quality head cleaning tape. If this fails, re-post, and I will explain how to clean heads by hand.

Dave Duff

Mar 01, 2008 | Panasonic PV-V4022 VHS VCR

1 Answer

Can not tape from cable, blue screen


If you have a cable box connected now, leave the VCR on channel 3 all the time and use the channels from the cable box.
The way this should be connected is cable in to cable box and cable out to VCR, VCR output to TV IN.
Hope this works for you.

Feb 11, 2008 | RCA VR348 VCR

1 Answer

Vcr does not respond to tv/vcr button on remote


You will not know from looking at the VCR if it is in VCR mode or TV mode. This is more likely a TV issue of whether the TV is monitoring the VCR or not. Make sure you have the TV selected so that it is monitoring the VCR.
That VCR/TV button has caused more confusion for the average person than anything else.
Hope Ya Fix It!

Jan 22, 2008 | JVC HR-J692U S-VHS VCR

2 Answers

I need to record a show


You have to make sure the channel on the vcr is set to 04 and the channel on your tv is set to 03. That's how mine works.

Nov 10, 2007 | Sansui VHF6010 VHS VCR

Not finding what you are looking for?
VCRs Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top VCRs Experts

 Grubhead
Grubhead

Level 3 Expert

4584 Answers

alexander woolfolk
alexander woolfolk

Level 2 Expert

276 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a VCR Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...