Question about GE WVSR1060A Top Load Washer

1 Answer

How does the top come off ge washer model wjxr2080t6ww

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,543 Answers

Use a putty knife to push the spring clips in where the top of the front panel meets the washer top, about 2 or 3 inches in from each side. Front panel pulls forward and lifts off pegs, revealing two 1/4 inch drive hex screws holding top to side panels. If your washer has the lid switch near the front, push the tab on the back side toward the center of the switch and push switch up, then twist 90 degrees and pass switch back through the opening. Now lift washer top at the front side. Most washer tops will unhook from the back side now, but some need to be slid an inch to the side yet to remove once the top is lifted a few inches. If you model still has the lid switch near the back of the washer opening, lift the top at the front and unhook the back of the washer top, pull the top forward a few inches and unplug the lid switch disconnect block. (two wires)

Posted on Oct 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Model wdss4120aww GE Washer is leaking


If it's leaking during the agitation cycle, and only in 'large' and 'super' water levels, then that's just the way the washer is designed. I got rid of that piece of junk.

Mar 03, 2013 | GE WBSR3140D Top Load Washer

Tip

How it works: Late model Ge top loading washer


The late model top loading GE washer is much different than it's original models that were so much more dependable than these newer ones are. To access the innards you must forst remove the front panel. Older models had the top pop up first but these newer models have the top bolted down. To get the top up you must first remove the front panel by using downward force on the top between the tiop and the front panel. It is not easy even for eperienced techs but cuss it a minute and it will come off. Once it is off you will notice the washer has an elecetric pump. Strings and junk get into this pump. It is easy to take apart and cleanup. The tub is suspended on 4 rods and the lateral movement is kept in check by 4 rubber cord mounted to the top called bungies. The motor and tranny can easily be accessed by removing the tub from the washer. After disconecting the power cable and pump the tub lifts out. Not all GE washers use the same motor or the same transmission method. Some do not even have a tranny. I have some GE washer service manuals.


GE front access late model washer





on Dec 13, 2010 | Washing Machines

1 Answer

Where do I find the model number on a top loader? ge hotpoint washer.


older models have a nomenclature tag with model and serial number at the base of the washer on the side in the rear. Newer models have it in the top on the backside of the controls.

May 12, 2011 | GE Hotpoint Super 3.2 cu. ft. Washer

1 Answer

GE top load Profile washer. Spin cycle not


Hi,
If you are having a problem with your top load washer then check out this tip...

Washing Machine2_bing.gif does not Pump or Spin
http://www.fixya.com/support/r4617986-washing_machine_not_pump_or_spin

If you are having problems with your front load washing machine2_bing.gif then checkout this tip...

Front Load Washing Machine2_bing.gif not draining and or not spinning
http://www.fixya.com/support/r4784376-front_load_washing_machine_not_draining

heatman101

Jun 11, 2010 | GE WVSR1060A Top Load Washer

1 Answer

My GE Model # WBB4500E1WW washer not spinning


the washer is on but not spining and the machine is about 6 month old

Dec 19, 2009 | GE WBB4500EWW Top Load Washer

1 Answer

We have a GE washer model WJRR4170E1WW. It works


There are little things that they call dog triggers that could be worn.
they should cost about $5.00

Sep 14, 2009 | GE WJRR4170E Top Load Washer

1 Answer

GE washer model #wle4000b1ww won't spin


This is joyce
You have a bad belt it wont pull the load.
thanks,
joyce

Feb 04, 2009 | GE WPRB9220D Top Load Washer

1 Answer

GE washer won't fill with cold water


Cold water pipe had become frozen. FYI this model of washer has a nice feature whereas you can test each component i.e. valves, by setting the timer and reading the LED's on the front panel. Instructions are in the schematic.

Jan 17, 2009 | GE Profile WPRE6100G Top Load Washer

Not finding what you are looking for?
GE WVSR1060A Top Load Washer Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...