Question about Asko W6661 Front Load Washer

1 Answer

Aski w6661 front load washer

My three year old played with the buttons and I have lost manual, so am unable to reset. Where can I get a manual or how do I reset.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Did you try unplugging the machine for at least 5 minutes.

Posted on Jan 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Help ! We have an L G front Load washer model # WM2016CW that leaks soap out the front bottom of the dispenser. It is 2 years old and I have followed all the manufacturers instructions on using HE soaps...


You can remove the dispenser and place it in the dishwasher for easy cleaning.
I have included some notes on your washer and I have a service manual for you HERE
themobilian_2167.jpg

Apr 07, 2011 | LG WM-2277HW Front Load Washer

2 Answers

Won't start


Hello, Have you checked the line fuses at the back of the washer ? The Asko washers will have 2x15amp "slo-blow" fuses which screw into a holder via a "hub" which turn's a quarter turn in or out. You will need either a replacement fuse or an ohm meter to confirm or dismiss the fuse or fuses being the problem. What to look for are 2 small gray circular button type things located by the cord with slots in the bottom for a screwdriver or flat blade of some kind to allow easy removal. Let me know how that goes and I'll try to assist you further if needed. Good luck and thank's for coming to "fixya". Please rate this info accordingly to it's helpfulness. Macmarkus :)

Apr 03, 2010 | Asko W6661 Front Load Washer

1 Answer

Please help me i lost my washing macine booklet and am unable to get a proper combination i have indesit washing machine wdl 106 i need a perfect combination about temp and all three knobs. cuz right now...


check the internet for a manual for your washer most of the time you can down load them. Put in the name and model number and state you are looking for manual.

Oct 31, 2009 | Indesit WA 125 Front Load Washer

1 Answer

My Asko W6661 washing machine water inlet fault would come on so I check the water inlet line and filter and everything was ok, but the water still would not come into the machine. I than check the...


As the solenoid should should remain power free and closed until the programmer tells the circuit board to switch on the power, it could conceivably be either or both of those things, though I feel the chances are greater the circuit board is at fault.

Apr 05, 2017 | Asko W6661 Front Load Washer

1 Answer

Asko Quattro 6661 water inlet fault


I had the same problem with my unit. The manual tells you to disconnect the water intake at the machine and clean the screen. This wasn't my problem because as you said the problem doesn't occur until the Rinse cycle which means there is water supply to start the Wash cycle.

From the back of the unit, remove the three screws and take of the lid. You'll notice that there are three separate motors do pump water inside the machine at the water intake. When standing in front of the machine, the motor on the right controls the rinse cycle. I connected an AC volt meter to that pump and started the rinse cycle. 240v showed up at the pump, but the water flow was poor. I simply squished up and down the rubber hose connecting this motor to the detergent unit and was unable to free the clog and water began to flow.

Jan 07, 2009 | Asko W6661 Front Load Washer

1 Answer

Where is the reset button for the Controls Locked to be released??


Press & hold down the 'end of cycle' signal button till the control light goes off

& rate me pl................

Jun 12, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Frigidaire Affinity/dr error


dr code means door not closed
get some crc spray and spray into lock on machine
that will lube the workings and should fix problem

Mar 13, 2008 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Over Flow Fault detection


Press "end of cycle" button; and wait for 2 minutes before trying the door. Do not force the door.

Rate me if helped please.

Jan 12, 2008 | Asko W6661 Front Load Washer

Not finding what you are looking for?
Asko W6661 Front Load Washer Logo

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

shaun taylor

Level 3 Expert

1525 Answers

Are you an Asko Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...