Question about Televison & Video

5 Answers

Bought remote from dollar store no instruction

Tv/catv/vcr/sat remote control lost the instructions to it. no name on remote to help.. how do I find the codes to progam our tv now. sanyo brand can any one help me.Thanks

Posted by on

  • 1 more comment 
  • greeneyes147 Oct 12, 2008

    they do not have any more!

  • Anonymous Jan 24, 2009

    Thank you u guys helped me thanks alot

  • Anonymous Mar 30, 2014

    Can you help identify this remote brand bought at dollar general and is model lm-1075

×

5 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I've bought the same remote control w/ out brand, and I've been using that for a long time. When I bought, it came w/ a manual w/ many codes... but u can use the general search that for me is better.

For example, you wanna fix a TV

1st - press SET button and the TV1 button AT THE SAME TIME (the RED light might be turned ON)

2nd - Press the SET buttton, and you'll see the red light shine, twinkle. (it means that the remote control is trying all codes)

3rd - while the red light twinkle, try pres the ON/OFF button... you should press the ON/OFF button many times, and when the TV turns off is because you found the code, so press TV1 button to stop the research in your remote control.

***PAY ATTENTION!!! If you don't stop the research at the same time that the remote control find the code, you'll lose the code... so you need restart everything again.

I hope it gonna help you!

Posted on Jan 11, 2009

  • stepugup
    stepugup Nov 19, 2012

    Very helpful. Thank you!!!!!!!!!!!!!!!!!! Looked for an hour for a code for this.

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have a code book if you need the codes

Posted on Nov 30, 2008

  • kween May 06, 2012

    I need a code to an esa tv

  • steven placencia Oct 12, 2012

    how do i program dollar store remote

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Go back to dollar store find brand and model and google it it will pull up a code book

Posted on Oct 12, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How do i program my 4in1remote control to work my jvc tv

Posted on Sep 04, 2012

Are there any numbers behind the batteries

Posted on Oct 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need coeds for sanyo


Hello
Setup code for Sanyo with One for all URC-3021 is
0154

The One For All 3 Device Universal Remote Control is preprogrammed at

the factory to operate an RCA TV, a Toshiba DVD player, and a Motorola

cable box.To control devices other than the default brands,perform the following
steps; otherwise skip this section:

Turn on a desired device (e.g.,VCR or DVD player) and, if

applicable, insert media (e.g., cassette or disc).

NOTE: Please read steps 2 through 4 completely before proceeding.

Highlight or write down the codes and device you wish to program

before starting step 2.

2. On the remote control,press a device key once (i.e., DVD/VCR,
CBL/SAT,or TV).

NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo,

or TV/VCR/DVD Player Combo press DVD/VCR once.After programming

a VCR Combo device, you will be able to control channel selection,

volume, and VCR functions.

NOTE: To program control of a DVD Player,DVD Player/VCR

Combo, or TV/DVD Player Combo, press DVD/VCR once.After programming

a DVD Combo device, you will be able to control channel

selection, volume, and DVD functions.

NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR)

Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)

Combo, press CBL/SAT once.

3. Press and hold SET until the LED (red light) blinks twice,
then release SET.

Use the Manufacturer's Codes to

locate the type of device and brand name and then enter

the first four-digit code for your device. If performed correctly,
the LED will blink twice.

NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter

the same code again.

5. Aim the remote control at the device and press POWER

once.The device should turn off. If it does not, repeat

steps 2 through 5, trying each code for your brand until

you find one that works. If it still doesn't work, try

Searching For Your Code on next page.

NOTE: If the device does not have a POWER key, press PLAY.

6. Repeat steps 1 through 5 for each device you want to control.

Mar 07, 2011 | One For All URC-3021 Remote Control

2 Answers

How can I get the 3-digit device code for a Sanyo TV Set? I lost the list!!


Hello
Three digit universal remote code for Sanyo are:
004/ 013/ 049/ 108/ 110/ 180/ 209

Four digit universal remote codes for Sanyo are:
0049 0097 0110 0004 0268 0012 0108 0180

Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.
  1. Manually turn on the device (TV, VCR, etc.) to be controlled.
  2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
  4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
  5. Press and release MUTE to install the code. The indicator light goes off.
Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.
OK.

Feb 20, 2011 | Universal Remote Control Remote Control

1 Answer

I need help to get a code for my sanyo tv and how to set it up.


Hi
Configuring codes:
1.Turn on a desired device (VCR or DVD player)

2. On the remote control, press a device key once (i.e., DVD/VCR,
CBL/SAT or TV).

NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo, or TV/VCR/DVD Player Combo press DVD/VCR once. After programming a VCR Combo device, you will be able to control channel selection,volume, and VCR functions.

To program control of a DVD Player,DVD Player/VCR
Combo, or TV/DVD Player Combo, press DVD/VCR once. After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions.

To program control of a Cable Box, Cable Box/PVR (or DVR)
Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.

3. Press and hold SET until the LED (red light) blinks twice,
then release SET.

4. Use the Manufacturer’s Codes to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly,
the LED will blink twice.

5. Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2 to 5, trying each code for your brand until you find one that works. If it still doesn’t work, try Searching For Your Code on next page

Auto Code Scan:
1.On the remote control, press TV once.

2. Press and hold SET until the LED (red light) blinks twice, then release SET.

3. Enter 9 - 9 - 1.The LED will blink twice.

4. Aim the remote control at the TV and slowly press POWER button.Stop when the TV turns off

5. To lock in the code, press and release SET.The LED will
blink twice.

6. To search for the codes of your other devices, repeat steps
1 to 5, but substitute the appropriate device key for the device you are searching for.

Code for sanyo tv is 0154
Thank You

Sep 13, 2010 | One For All URC-3021 Remote Control

1 Answer

Lost code booklet for my oneforall remote


I can help you with your URC-3021 Universal Remote Control issues.

The codes for Sanyo TVs is: 0154.
The codes for RCA DVDs are: 0522, 0571, & 0717.
The codes for Magnavox DVDs are: 0503, & 0675. These may or may not work with newer Blu-Ray players. Since you have two disc players, you will need to reassign the CBL/SAT key to act as a second DVD key.
I don't believe the URC-3021 stores codes for surround sound amplifiers: it has only three function buttons: TV, DVD/VCR and CBL/SAT.

For complete instructions on entering the URC-3021 remote codes, please refer to my posted Fixya Tip One For All URC-3021 Code Entry.

I hope that helps.
_______________________________________________
Reassign URC-3021 Device Key
Urc-3021 Code List Download
One For All URC-3021 Code Search

Feb 13, 2010 | One For All URC-3021 Remote Control

1 Answer

Need to program rca univ remote for sanyo tv & i lost the manual


Get your Sanyo TV codes and one by one program the into you RCA universal until you can turn the TV on and off. Find codes at Sanyo.com, the manual, Sat Manual, Vcr Manual etc.

Sep 19, 2009 | RCA Universal Remote Control

1 Answer

Need code list for a sanyo tv and progam instructions


Here is a useful link that i found for you.
http://www.ehow.com/how_9191_program-rca-universal.html
I hope i have been helpful Regards

Jul 20, 2009 | RCA Universal Remote 3 Device Remote...

2 Answers

Intructions for programming a remote control


I own this remote. Here are the instructions.
1 turn on your tv or catv
2 aim remote at tv or catv
3 while holding tv or catv button press 0 to 9 last ch 100/ent or channel
4 release both buutons when tv or catv changes channel.
note press tv or vcr or catv button first to select desired function

Mar 06, 2008 | Hitachi VT-RM380A Remote Control

3 Answers

Lost codes for 4 in one used for universal remote control


DRC800 Sanyo TV 0799,0154,0893 Panasonic VCR 0035,0162,1062,0616,0225,1035 press device key for 6 seconds led will blink solid key in code correct code will cause led to blink 3 times press power button to confirm code works. rg

Sep 09, 2007 | Philips 8-Function Universal Learning...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

6,116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69736 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6370 Answers

yadayada
yadayada

Level 3 Expert

63661 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...