Question about Dynex Enhanced-G Wireless Broadband Router

1 Answer

I LOST MY INSTALLATION DISK FOR MY ROUTER, IS THERE ANYWAY I CAN GET THAT DRIVER ONLINE?

Posted by on

  • bdbootsy Oct 25, 2008

    need to release for set up of xbox 360 again

  • pompper87 Jan 25, 2009

    I cant figure out how to create a network key

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

This router does not need any drivers. The users manual can be found here: http://www.dynexproducts.com/skins/skin_1/Topics/Documents/07-366%20DX-WEGRTR%20combined%20-%20WEB.pdf
Without the cd you won't be able to use the easy setup wizard, but you can still configure the device. Starting on page 15 half way down it talks about setting up your router using the web-based advanced user interface. Using that information you should be able to configure your router.

Posted on Oct 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lost my cd for net gear wireless-N Dual Band WNDA3100v2 how can i get another one


Are you trying to set up router ?
You can set up your router manually, without the CD.
Make sure that your computer is able to go online directly through the modem.
If your computer is able to go online through the modem, that means the modem is working fine.
You will need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.

Click Here for more information about the routers and network

Aug 26, 2010 | NetGear RangeMax Dual-Band Wireless-N...

1 Answer

Can't log on to my wi-fi ipod lost my password


Your wireless network must be secured
You will need to check the wireless settings of the router.
Is there any computer online using the router.
check the IP address on that computer.
If yes then you can open the router set up page on that computer.
router set up page is the page where you can check all the router settings.
Click Here for more information about the routers and network

Jul 04, 2010 | Computers & Internet

1 Answer

The wireless network is being picked up by the laptops in the house, but there is no internet connection between the modem and the router. MY router is a Belkin G Wireless


if you connect the computer directly to the modem, does it work?
If your computer is able to go online through the modem, that means the modem is working fine.
You will need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.

Click Here for more information about the routers and network

Mar 06, 2010 | Belkin Wireless-G Plus MIMO Router with...

2 Answers

I can't log on to my router and can't log on the internet


Router comes with instructions with a login name and default password. Try logging in that way. If you can't log in to the internet, do a full power down, making sure to unplug modem, then router, leave off for at least 1 minute. Then replug and power up. See if that does it.

Jul 24, 2009 | Belkin Wireless-G Plus MIMO Router with...

1 Answer

Need program


You can go online to the manufacturers website and download the newest drivers for your router.

Mar 24, 2009 | Dynex Enhanced-G Wireless Broadband Router

1 Answer

Installing ntgear rangemax wireless router


take this information and notice the stars:
Start-> Run-> cmd [enter]
ipconfig [enter]
You will probably see:

IP: 192.168.*.2
sub: 255.255.255.0
gateway 192.168.*.*

Go to an Internet Browser and type in this from the *GATWAY* in the address bar:
http://192.168.*.*

* This will likely be 192.168.1.1 / 192.168.1.254 192.168.0.1 /254
* or maybe even 192.168.2.1 / 254

username and pass will be admin admin or admin 1234 admin and no password or maybe no username and admin as the password...
Configure the router as you see fit.

Oct 26, 2008 | Belkin Wireless-G Plus MIMO Router with...

1 Answer

Installation CD


I lost my installation CD and received these instructions from the Belkin Tech Support, and was able to install the Wireless N Router with no problems.
Follow the steps given below for configuring the Belkin N router manually.
- Connect the computer to the "LAN" port on the router and connect the modem to the Internet/"WAN" port, using Ethernet cables. 
- Take a paper clip, insert the paper clip in the reset hole of the router and hold it for 15 seconds.
- The power light will flash and then come back "ON" solid, indicating that the router is being restored to factory defaults.
- The corresponding lights on the front of the router should be lit up.
- On the computer, check if you have an IP address in the range of 192.168.2.x.
- If not, specify a static IP address, gateway and "DNS" address by following the steps given in the link-
http://web.belkin.com/support/kb/kb.asp?a=2824 
- Log on to the router web interface by typing in http://192.168.2.1, in the address bar of your browser.
- By default, the password is blank.
- Click on "Connection Type" in the left hand column under "Internet WAN" heading.

If the connection type is Dynamic (cable):

- Choose "Dynamic" and then click on "Next". 
- Type in your “Host Name”, if you’re Internet Service Provider has provided it. Else, leave it blank.
- Click on "Change WAN MAC Address".
- Click on the button "Clone".
- Click on "Apply Changes". 

If the connection type is PPPOE (DSL):

- Choose "PPPOE" and click on "Next".
- Enter the user name and password given by your Internet Service Provider.
- Save the settings.
- Click on the "Home" link at the top of the screen. 

Internet Status should show "Connected" on the top right hand corner of the web page.

If the problem persists, please get back to us with the following information:

1. Type of connection provided by your ISP (Is it PPPOE, Dynamic or static).
2. Name of the Internet service provider (ISP).

Aug 11, 2008 | Belkin Wireless-N Wireless Router with...

1 Answer

Wireless g router


Here it is.

Note: you need Adobe PDF Reader. you can download it here.

Aug 04, 2008 | Dynex Enhanced-G Wireless Broadband Router

1 Answer

Belkin wireless g router


Have you tried e-mailing Belkin Customer Support? I had a similar problem, with my PC, they sent the info I needed and I was on line in under 6 minutes (this after spending many frustrating hours scouring the internet).

May 23, 2008 | Computers & Internet

Not finding what you are looking for?
Dynex Enhanced-G Wireless Broadband Router Logo

Related Topics:

319 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dynex Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Prashant M
Prashant M

Level 3 Expert

2259 Answers

micky dee

Level 3 Expert

2638 Answers

Are you a Dynex Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...