Question about Kirby Vacuums

1 Answer

I have a belt that broke on an older Kirby sweeeper

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 99 Answers

This can be supplied on model no.By us and posted out

Posted on Oct 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kirby G4 running very loud and smells hot.


were you put the belt on see if any thing is rubbing against shaft.it may have been the belt,replace the belt and clean out the bab and also the floor brush.

Jul 31, 2010 | Kirby G4 Bagged Upright Vacuum

1 Answer

My belt broke on my kirby G-5. I havent put a belt on it in 10 years. I having problems getting it on.Can u tell me the right way? Thank you.


Greetings,

I recorded a video repair of replacing the belt for the Kirby generation vacuum cleaner. The following video will walk you through step by step on how to replace your Kirby belt, as well as doing some basic maintenance to the roller brush to prolong the life of your belt as long as possible.

How to Replace the belt on a Kirby Ultimate G Vacuum Cleaner;




I hope that this video was helpful to you in repairing your Kirby. If you found the video to be helpful, please kindly rate the video helpful by clicking on the Thumbs Up Icon below.

Thanks for watching!

Chris J.

Nov 21, 2009 | Kirby Ultimate G Bagged Upright Vacuum

1 Answer

Belt broke on shampooer


there are screws on the ends. I got it fixed.

Apr 11, 2009 | Kirby Ultimate G Bagged Upright Vacuum

1 Answer

Kirby ultimate G .accessory lock is striped. Can that be replaced?


http://geeksquad.fixya.com/ThreadView.aspx?prdid=11557&thid=559479
Kirby ultimate G .accessory lock is striped. Can...
Posted by goulds5 on Apr 30, 2008
Kirby ultimate G My belt broke & sucked into my sweeper & got stuck. My husband had to take it a part, he go out the belt but the accessory lock now is striped. Can that be replaced? Have you ever heard of this?

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. Yes, the accessory lock can be replaced but it may be part of the actual vacuum head of which could be expensive, it may be molded onto the vacuum head and would be replaced. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

http://kirby.com/ Customer Service – United States & Canada 1-800-494-8586
Hours 8:00 am to 5:00 pm (EST) U.S. & Canada Fax # 1 (216) 529-6146
Mail To:
Consumer Relations
The Kirby Company
1920 West 114 Street
Cleveland, OH 44102
Thanks, Don the Vac Man
Go Ahead. Use Us.


Apr 30, 2008 | Kirby Ultimate G Bagged Upright Vacuum

1 Answer

How do you replace the belt on the Kirby, Model No D50, Serial No. A442867


Generic problem for all Vacuums
How do you replace the
How do you replace the belt on the Kirby, Model No D50, Serial No. A442867

I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
This is an older Kirby vacuum and the front brushroll section of the vacuum and the front brushroll section will come off, 1st you have to remove the front cover (the Kirby Emblem) and under that there is a Kirby spoon or hook and you need to dial off the belt off the belt shaft, once that has been done remove the bottom plate and un-install the Kirby brushroll, check to see if the brushroll spins freely, if it does go onto the next step, if not clean off the hair and thread from either end and then re-check the brushroll, if it still binds up then replace the brushroll and belt with Genuine Kirby belt and brush. Then use the dial to place the belt onto the Kirby spoon / hook. Once the belt is on the hook, install the bottom planter and place then housing of the Kirby on the vacuum and use the lever on the top to secure the fan housing dial the belt onto the pulley and you should be good to go.
http://kirby.com Contact Us by Phone
United States and Canada 1-800-494-8586
Between the hours of 8:00 am to 5:00 pm EST
Monday thru Friday


Don – The Vac Man

Apr 21, 2008 | Vacuums

2 Answers

Belts


Recently received a kirby from mother in law and don't how to change the belts

Dec 15, 2007 | Kirby Ultimate G Bagged Upright Vacuum

Not finding what you are looking for?
Vacuums Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kirby Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Roger Potts

Level 3 Expert

694 Answers

Are you a Kirby Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...