Question about Kyocera Fax Machines

1 Answer

I have a KM-3060, I would like to turn off the feature that after I scan a file into and SMB folder, it prints a confirmation page.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,120 Answers

Browse your scanner defaults menu.

Posted on Oct 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My photocopier km 3060 displays error code c0120.what is the problem and the solution


Hi
I have found a list of error codes at the link below and your code is described as;
Drum EEPROM error Reading from or writing to EEPROM cannot be performed. Poor contact in the connector terminals. Defective drum unit. Error Codes Kyocera Mita KM3060
It looks therefore like a drum unit problem which probably requires a replacement drum unless you can check and improve the contacts in the connector terminals.
Hope this is helpful, if so would you please register that with Fixya
Cheers

Oct 17, 2014 | Kyocera Km 3060 Digital Copier With...

2 Answers

Kyocera error c7200


km 6030 machine have a code on screen c7200 so how i solve it

Dec 18, 2013 | Kyocera Km-6030 With Feed, Finisher, Bank,...

1 Answer

How do you keep people from being able to use the maintenance key on kyocera km3060


Change the admin password on it. Or if not feasible, then put a sticky label over the button.

Nov 22, 2013 | Kyocera Km 3060 Digital Copier With...

1 Answer

Brother FAX-8070P memory shows full and does not send all pages at one time?


This message means the memory capacity of the unit has been exceeded. The amount of memory used depends on the amount or type of data on the documents being faxed or copied.
  1. If you get an "Out of Memory" message while scanning the first page of a fax, press Stop/Exit to cancel scanning.
  2. If you get an "Out of Memory" message while scanning a subsequent page, you can either press Fax Start to transmit the pages that were scanned so far or press Stop/Exit to cancel the operation.

When Fax Storage is set to On, a copy of all received faxes are stored in the memory, thus using up a % of the memory available for other functions.
The Fax Storage feature is utilized for Fax Forwarding, Fax Paging and Remote Retrieval. If you do not need these features, verify Fax Storage is set to Off by doing the following:
  1. Press the Menu/Set key.
  2. Press the arrow key until FAX appears on the LCD. Then, press Menu/Set.
  3. Press the arrow key until REMOTE FAX OPT appears and then press Menu/Set.
  4. Pressthe arrow key until FAX STORAGE and then press Menu/Set.
  5. Check the setting. The display will read ON or OFF. If the setting is ON, press the arrow key until the display reads OFF.
  6. Press Menu/Set.
  7. If you have faxes stored in the memory, you will receive a message that reads Erase all fax? 1. Yes 2. No. If you want to erase all the faxes in the memory without printing them out, press 1 (Yes) and then press Stop/Exit.
Note
    If you would like to reprint the saved faxes, press 2 (No), press Stop/Exit and continue to the following steps for instructions on how to print stored faxes.
If you do need the features that require Fax Storage to be On, the stored faxes will need to be erased or printed to remove them from the memory and to allow additional memory to be available. Follow these steps to print the stored faxes:
  1. Press the Menu/Set key.
  2. Press the arrow key until FAX appears on the LCD and press Menu/Set.
  3. Press the arrow key until REMOTE FAX OPT appears and then press Menu/Set.
  4. Press the arrow key until PRINT FAX or PRINT DOCUMENT appears and press Menu/Set.
  5. Press Fax Start.
  6. After printing is finished, press Stop/Exit.

Jun 06, 2011 | Brother FAX-8070P Plain Paper Laser

1 Answer

My brother MFC 8500 is receiving alright but everything I send out has a big black streak going down the right side of the page. Confirmation page also has big black streak.


Let me see if I got this right.

The received fax is clean but when you send one out it has a black streak on it.
Cool! So far so good.
Makes sense because for sending, the fax scans the original document and parts of the scanning area could be dirty and so on. Therefore a black streak may appear.
The same black streak would also appear when you make a copy, because the original document must also be scanned.
Logical!

However for receiving faxes, the machine uses the internal memory and the print engine only, and the same applies to printing the transaction report, which comes from inside via the print engine.
The scanner has no rol in either situation.

Now I'm lost!

.

May 31, 2011 | Brother Fax Machines

1 Answer

How to stop to print the journal after send fax everytime?


Sending Confirmation
This report shows the fax number, the number of pages, elapsed time of
the operation, the communication mode, and the communication results.
You can set up your machine to print the message confirmation report in
one of the following ways (see page 5.3):
• Automatically after each transmission (ON)
• Automatically only if an error occurs during transmission (ERR)
• No report printed at all (OFF). You can print this report manually at
any time you want.
SENDING CONFIRM - A confirmation report shows whether the
transmission was successful or not, how many pages were sent, etc.
Select ON to print a confirmation report automatically each time you
send a fax.
Select OFF to turn this feature off.
Select ERROR to print only when an error occurs and the transmission
was not successful.

Nov 27, 2010 | Samsung SF-5100 Plain Paper Laser Fax

1 Answer

My HP 1040 fax prints a sending confirm notice after every fax is sent. Is there a way to turn this feature off as it is a major waste of paper.


Reports you can print
You can print these reports whenever you need to. Some of these reports can be set to print automatically also.
1. Press Report/Help.
2. Choose the report you want by using left or right arrow.
3. Press Start/Enter when the desired report is displayed.
4. The selected report will be printed.

Sending Confirm
A confirmation report shows whether the transmission was successful or not,
how many pages were sent, etc.
ON: prints a confirmation report automatically each time you send a fax.
OFF: never prints a confirmation report (You can print one manually using the
Report/Help button (see Print reports on page 51).
ERROR: prints only when an error occurs.

Nov 25, 2010 | HP 1040 Plain Paper Inkjet Fax

1 Answer

Confirmation page needed


Press MENU - 2 4 1 then you can choose to have that feature ON or OFF. the +Image means that it will also print a copy of the first page sent so you can actually verify the document sent.

Mar 31, 2010 | Brother IntelliFAX 4750 Plain Paper Laser...

1 Answer

Confirmation pages


press function
press dataregistration
press set
use scroller up and down to select the function that you want to do, there's a lot of function, like user setting, report setting vvvvv.

select user settings, then scroll up or down
select activitiy report, then set it auto print off

will help you, play around with it.

Oct 22, 2007 | Canon FAXPHONE L80 Laser

Not finding what you are looking for?
Fax Machines Logo

Related Topics:

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kyocera Fax Machines Experts

NewYork kyocera HP...

Level 3 Expert

513 Answers

Ngoro
Ngoro

Level 3 Expert

1111 Answers

rdjagger

Level 3 Expert

1692 Answers

Are you a Kyocera Fax Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...