Question about Intel Motherboard

1 Answer

Monitor goes into stand by when conection to tower is turned on

No power to monitor when connect top mainboared ...but when take monitor off power to monitor restored

Posted by on

  • Saxyguy Oct 11, 2008

    Sounds like the problem I'm having that is a bit puzzling... A little more info: Motherboard powers up, cpu and case fans spin and HD starts up. The puzzling part is that cpu fan goes full blast and won't slow down. When the problem began that was intermittant, if I restarted it a couple times the fan would calm down and I'd get video but as long as the fan is spinning fast like that-no video. I tried a pci video card but still nothing. I can't help but think it's a bios issue of some kind. I thought maybe a reset would help so checked MSI site for info the only manual they have is for 7207 V2.2 and my board is V1.0 and doesn't have the bios reset button like the one they show. There is a green jumper near the bios chip but I'm not sure if that's it or how to reset with it if it is. I tried taking the battery out for a few minutes but that didn't help. If it is a problem with the board I can replace it fairly cheap but could it be the cpu? Any thoughts would be unbelievably appreciated!

  • bharatkumar3 Nov 05, 2008

    the time I switch on the system only fan start for some time and then stop .But meanwhile there is no display on the monitor. Is it problem with the power chip of the motherboard.what is the processor to solve this problem.My motherboard is under warranty can anybody tell me the intel service center address or the phone number. Please help me.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 141 Answers

Try a video card connect bottom motherboared!!!!

Posted on Oct 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When i turn on tower a blue light comes on, the monitor comes one for a moment an says power saver and then it goes off.


This means that your monitor is not getting any signal from your video card. Check if the monitor cable is properly plugged in. if it is try connecting another monitor to your tower. If That fails theree must be some problem with your video card..

Feb 28, 2011 | Computers & Internet

1 Answer

My desk top computer monitor will not come on, but the tower will light up, could it be a virus..if so how do i fix it


A couple things to consider ... Are you certain the monitor is plugged in ... is there power in the outlet/power strip ... is the power strip turned on ... can you try another outlet close by ... is the power light on the monitor lit? Are both ends of the video connection connected? Are you using on-board video adapter or a adapter card? Is it properly plugged in. Do you have a second monitor you can temporarily connect to your tower? (like a lap top that you can connect with a VGA cable?) Can you try your monitor with someone elise's computer? If your monitor doesn't work on another known good computer ... it could be your monitor needs replaced.

Thanks for your question

Nov 30, 2010 | Computers & Internet

2 Answers

I have a dell optiplex sx280 computer and monitor that has lapsed into ''power save mode'' and I have been unable to ''awaken'' it (I'm not sure which is ''asleep'': the monitor or computer!) from sleep. I...


How's the status light of your computer monitor? is it blinking amber? and the status light of your computer tower's power button? blinking amber as well or solid green or no light at all?

1. Disconnect all the connection at the back of your computer tower
2. Press the power button of the computer tower for 15 seconds
3. Reconnect the power button and the monitor cable at the back of your computer tower and turn on the computer (if it turned on that means that one of the device plugged at the back of your computer tower is faulty)
4. If still the same problem, open up your computer tower.
5. Reseat the video card, Reseat Hard drive, Reseat Memory, Reseat CPU, Reseat power cord coming from the CPU to your computer (doing all things one-by-one to pin-point the root cause of the issue)

If none of the troubleshooting steps fixed the problem, possible that the power supply is faulty and if the power supply is faulty sometimes it goes with the motherboard.

Jan 08, 2010 | Dell OptiPlex SX280 PC Desktop

1 Answer

Mx75 monitor turns off when I awaken my computer


right click on desktop select properties(screen saver ) select monitor button in that select turn monitor never.(configure carefully)

Nov 24, 2009 | HP Pavilion MX75 17" CRT Monitor

1 Answer

My monitor shuts down after one second.


Dell monitors automatically go into power-save mode after a preset amount of time when the computer is inactive. The Dell monitor will go completely black, instead of showing a screensaver. This doesn't mean that your Dell computermag-glass_10x10.gif has shut down. Instead, this allows your monitor to essentially turn off until it's needed again. You can change how long it is before the Dell monitor goes into power-save mode by changing your display settings.
  1. Step 1 Press any key on your keyboard or move your mouse. Either will turn off power-save mode. Alternately, you can press the power button on your Dell computer tower or laptop.
  2. Step 2 Press any key a second time if the monitor goes from power-save to stand-by mode. Stand-by mode allows the screensaver to appear.
  3. Step 3 Enter your user name and password into the login prompt if your computer requires a login. Press "Enter" to begin using your Dell computer.
  4. Step 4 Change the display settings on your Dell monitor to prevent your monitor from going into power-save mode prematurely. Right-click anywhere on your desktop and choose "Properties." Click the "Screensaver" tab and press "Power." Beside "Turn off Monitor," choose a time amount from the drop-down list and press "Apply."

Nov 13, 2009 | Dell Dimension 3100 PC Desktop

1 Answer

Computer will not power up.tower light stays yellow instead of blue


check whether the monitor cable is conected with the cpu(tower) becuase if the monitor is not recieveing the signal from the tower means you will get this issue.

Nov 11, 2009 | Computers & Internet

1 Answer

Wont post led 3 flashes


if its the red flashing light on the tower, its the hard drive activity light.

when the monitor goes on stand by, does the tower retain power? (green light on and flashing red light sometimes?) Does your keyboard's scroll lock/num lock/caps lock keys and keyboard lights work?

Sep 07, 2009 | AOpen AX4SPB-UN (91.8AT10.013) Motherboard

1 Answer

Monitor will not stay on


HOw about the light on the tower? if its stedy green then the tower is ok then run a self test on monitor if it passes the monitor is also ok then unplug the power cable from the monitor and data cable also and press and hold the power button for 10 sec and then connect the monitor to the system

Jul 02, 2009 | Computers & Internet

2 Answers

Dell tower desktop Dimension 5100. Tower makes whistling sound.


sounds like it could be a bearing in your hard drive. is this problem constant? If so, I would open up the tower and disconnect the hard drive and then power up the tower again. if the sound goes away--you need to get a new hard drive. If not, you could have some dust bunnies in your cooling fan.

Jun 15, 2009 | Dell Dimension 5100 (D51L1) PC Desktop

3 Answers

Power saving mode upon start up




i) usually an computer enter's into power saving mode if computer monitor is not receiving any singals from the computer tower, so it has nothing do withur computer monitor(computer monitor is working fine), there is some problem withur computer tower.

ii) now try  removing all the physical connections going to computer tower(back side), wall socket  and replace them ....., (to avoid loose connections) 

   now see whether ur computer is turning on and working properly so that your computer monitor receive singals ....

  let me know what is happening

Thanking you

M. Sridhar

Jan 01, 2009 | HP Pavilion a450n PC Desktop

Not finding what you are looking for?
Intel Motherboard Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Intel Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Tony

Level 3 Expert

2598 Answers

David
David

Level 3 Expert

778 Answers

Are you an Intel Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...