Question about Kenmore Washing Machines

1 Answer

How do I open the top of a Kenmore washer 80 series. Model 11092284100?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 943 Answers

HI thanks for your question. 2 screws on each side of console. remove. lift up console. 2 brass clips , remove. disconnect lid switch connector. pull cabinet off. thanks the appliance doc. please rate my answer thanks.

Posted on Oct 09, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have a Kenmore 80 series top load washer model 110.28803890. When the timer moves to spin it makes a load clicking noise and does nothing.


Timers are not supposed to make loud clicks. If it is, it's going bad. The same problem happened with my parent's Estate washer. It its on it's third timer!

May 24, 2012 | Kenmore Washing Machines

1 Answer

80 series model#26852504. just replaced the trans and now i have to open and close the lid to get the drum to spin


I don't get cold water in the washer. I even changed my water inlet valve. I don't know what else I have to look for. Please post me the solution. The model is Kenmore 80 series-110 26852504

May 17, 2011 | Kenmore 24032\24036 Top Load Washer

1 Answer

How do I replace lid switch in a Sears Kenmore 80 series, model 1


The following link explains step-by-step how to replace a lid switch on a Kenmore top loader:

http://www.fixya.com/support/r3557193-replacing_a_lid_switch

If you have any questions about this repair, please post back and let me know. I hope this helps you.

NOTE: Kenmore is manufactured by Whirlpool so these instructions will apply.

Apr 07, 2010 | Kenmore 24032\24036 Top Load Washer

3 Answers

How many cubic feet are in the Kenmore Washer Model 110 80 series


The cubic feet of the Kenmore washer model 110 heavy duty is 2.8 cubic feet. Measured to the top water line 14.5 inches and using the radius of the tub of 10.375 inches.

Oct 26, 2009 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

Kenmore 80 Series will not fill up with water


if your washer will agitate when set to fill but not fill, then your pressure switch is bad.
also you may want to check and see if you are getting both hot and cold to your washer.

Nov 24, 2008 | Kenmore 24032\24036 Top Load Washer

2 Answers

Kenmore 80 Series Top Load Washer not agitating


Check out this you tube. Had the same problem today. Tipped washer on its side and replaced coupler between motor and gearbox. Parts are about $15
This is a good diagnosis video.
http://www.youtube.com/watch?v=VYOP0_KCYT0

Sep 02, 2008 | Kenmore 24032\24036 Top Load Washer

Not finding what you are looking for?

Open Questions:

0 Answers

Kenmore Elite HE4T Washing Machine Diagnostic Test Didn't complete and clothes aren't spun as dry as in the past I have a Kenmore Elite HE4T washing machine and I noticed that recently it isn't getting all of the clothes completely dry from the final spin cycle. Thus, the dryer has to run through two cycles to get the clothes dry. I did a bunch of research and made sure there weren't any kinks or blockages in the drain lines; and opened up the bottom of the washer and cleaned out the drain cleanout. I found a few pennies, but everything seemed to be working ok. I ran a load and had the bottom open so that I could make sure the motor, drain and belt were all working properly. The drain does get the water out of the washer, so the clothes aren't sitting in water, they just don't seem to be spun as fast or as long as they used to. I always put it on the "extra high" spin setting no matter which type of load I run. So, I found a way to run the diagnostic test on the washer and it went through C0-C5 (the agitation step) and all worked great, until it wouldn't come out of C5 after at least 10 minutes and go thru C6-C8. I had to cancel the diagnostic test and hit the "drain and spin" button to get all of the water back out of the washer. BTW, the "drain and spin" seems to get the clothes a bit drier than when I have it run through the "normal" cycle with the "extra high" spin. If anyone has any other thoughts, I would really appreciate it. This unit is in a small space with the dryer attached so to take it out and do repairs is a pretty big hassle. It has had a new control board and two new fill valves in the 10+ years that I have owned it. Questions I have: 1.should I remove the entire drain pump to make sure there isn't anything lodged in it? 2. could it be the belt slipping slightly and keeping the spin from reaching its 1200 RPMs? 3. Anything else I may be missing???

Jan 17, 2017 | Kenmore Washing Machines

Washing Machines Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Archaeology
Archaeology

Level 3 Expert

662 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...