I keep trying to set it to have 2 .00 like 2.35 cents. I for some reason it got changed and I cannot get it back to just the 2.Decimal points.

You have to make sure that the third set of buttons wit the K*A is set to A and the 5th set of buttons is on the 2.

Posted on Dec 16, 2008

Hi,

a 6ya expert can help you resolve that issue over the phone in a minute or two.

best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).

click here to download the app (for users in the US for now) and get all the help you need.

goodluck!

Posted on Jan 02, 2017

By default the calculator is set to display two digits after the decimal point (for dollars and cents). If you'd rather have no digits after the decimal point, press 2nd [FORMAT] 0 .

Alternatively, you can press 2nd [FORMAT] 9 for floating decimal.

Alternatively, you can press 2nd [FORMAT] 9 for floating decimal.

Sep 17, 2012 | Texas Instruments BA-II Plus Pro...

Non-printing models (also applies to HR-8TE printing calculator):

1. Press [AC]

2. Hold [SET/%] key for about 2 seconds

3. Press [TAX+]

4. Input the tax rate

5. Press [SET/%]

Printing models (except HR-8TE):

1. Have calculator in "print" mode

2. Press [CA]

3. Hold [SET/%] key for about 3 seconds

4. Input the tax rate

5. Press [TAX+]

6. Press [SET/%]

^Top

Enter only the numerals, not the letters.

^Top

The attached chart shows comparisons of the different calculator models. This includes graphing, scientific and printing calculators. download the chart here

^Top

The HR-8TE/HR-8TM have a [DEC] key with F, 0, 2, and 5/4 over it, while many other calculators models have a switch labeled [F CUT 5/4].

The button or switch can control rounding off to a certain number of decimal places. F is floating point (no F indicator on screen), 0 rounds off to 0 places after decimal point, and 2 rounds off to 2 places after decimal point.

The 5/4 applies to either the 0 or 2 modes, and describes the type of rounding off that is performed. The calculator will round down if the digit after the one you are rounding to is 4 or lower, and round up if the digit is 5 or higher.

^Top

This switch is used to determine how many decimal places your answer is displayed in.

ADD (2) is often used for monetary calculations, so that it is not necessary to enter the decimal point. It is automatically placed two decimal places from the end for cents. For example, entering 123 will display as 1.23.

^Top

This is a markup on price procedure. The formula is as follows:

Markup%=(Markup Price-Cost)/(Markup Price)

^Top

Make sure that you are following the correct procedure.

Adding 10%: 200 [×] 10 [%] [+]

Subtract 10%: 200 [×] 10 [%] [-]

^Top

AP Calculus requires a graphing calculator.

Any graphing or scientific calculator is permitted on the following as long as it does not have a QWERTY keyboard, electronic writing pad or a pen-input/stylus-driven interface:

PSAT/NMSQT, SAT I

SAT II Math, IC & IIC

AP Statistics (graphing expected)

AP Chemistry

AP Physics

May 27, 2011 | Casio Parts Cash Register PC Desktop

The selector you are asking about is the "decimal selector". The result displayed/printed, will be in a format according to the position that you have selected as follows:

f = floating (the result will be in the number of decimal places that were entered on the keyboard

4= fixed 4 decimal places (x.0000)

3= fixed 3 decimal places (x.000)

2= fixed 2 decimal places (x.00)

0= fixed 0 decimal places (x)

add 2= (add mode*,fixed 2 places) ($.00)

Note* "ad mode" automatically enters the decimal place when entering the number on the keyboard. If you enter "123", the displayed ammount will be "1.23". If you enter "1", the display will read ".01". This is a useful setting when adding a list of numbers in a dollars/cents format, however, be careful, if entering a whole dollar ammount "three dollars" be sure to enter the decimal point, or enter the number as "300". If you don't, the result will be ".03", instead of the 3 dollars you intended.

f = floating (the result will be in the number of decimal places that were entered on the keyboard

4= fixed 4 decimal places (x.0000)

3= fixed 3 decimal places (x.000)

2= fixed 2 decimal places (x.00)

0= fixed 0 decimal places (x)

add 2= (add mode*,fixed 2 places) ($.00)

Note* "ad mode" automatically enters the decimal place when entering the number on the keyboard. If you enter "123", the displayed ammount will be "1.23". If you enter "1", the display will read ".01". This is a useful setting when adding a list of numbers in a dollars/cents format, however, be careful, if entering a whole dollar ammount "three dollars" be sure to enter the decimal point, or enter the number as "300". If you don't, the result will be ".03", instead of the 3 dollars you intended.

May 20, 2011 | Royal 29307U Calculator

Decimal Point and Separator Symbols

You can use the display setup (Disp) screen to specify the symbols you want for the decimal point and 3-digit separator.

• To change the decimal point and separator symbol setting, press the MODE key a number of times until you reach the setup screen shown below.

Display the selection screen. (Disp) 1.

Press the number key ( 1 or 2) that corresponds to the setting you want to use.

1(Dot): Period decimal point, comma separator

2(Comma): Comma decimal point, period separator

You can use the display setup (Disp) screen to specify the symbols you want for the decimal point and 3-digit separator.

• To change the decimal point and separator symbol setting, press the MODE key a number of times until you reach the setup screen shown below.

Display the selection screen. (Disp) 1.

Press the number key ( 1 or 2) that corresponds to the setting you want to use.

1(Dot): Period decimal point, comma separator

2(Comma): Comma decimal point, period separator

Nov 27, 2010 | Casio FX-300MS Calculator

If I am not mistaken you are trying to set your decimal in dollars and cents correct? Well, if I am understanding your question correctly; you move tab that has F 6 3 2 1 0 set that to the 2 and then there is a tab that says "K * A make sure that is set to the A as well. Hope that helps.

Nov 19, 2008 | Sharp EL-2196BL Calculator

How many decimal places are in the answer of this problem? 3.7844236 times 456.93874513

Jun 04, 2008 | Canon LS-100TS Calculator

Set the +43210F switch to + (or 2).

On some models it is A43210F, then use A (or 2).

+ mode will let you enter numbers (monetary) without the decimal point and assumes cents; 2 mode will just round to 2 decimals, but you must enter the decimal.

On some models it is A43210F, then use A (or 2).

+ mode will let you enter numbers (monetary) without the decimal point and assumes cents; 2 mode will just round to 2 decimals, but you must enter the decimal.

May 05, 2008 | Office Equipment & Supplies

To enter the date

1. Be sure to switch to "rate set" from GT

2. Enter the month

3. Press the decimal point

4. Enter the day

5. Press the decimal point

6. Enter the year

Example 3.09.2007

7. Press the button that look like a clock/calendar

To enter the time

1. Be sure to switch to "rate set" from GT

2. Enter the hour (please use military time)

3. Press the decimal

4. Enter the minutes

Example: 13.24 or 9.24

5. Press the button that look like a clock/calendar

Then change the "rate set" back to the GT setting.

1. Be sure to switch to "rate set" from GT

2. Enter the month

3. Press the decimal point

4. Enter the day

5. Press the decimal point

6. Enter the year

Example 3.09.2007

7. Press the button that look like a clock/calendar

To enter the time

1. Be sure to switch to "rate set" from GT

2. Enter the hour (please use military time)

3. Press the decimal

4. Enter the minutes

Example: 13.24 or 9.24

5. Press the button that look like a clock/calendar

Then change the "rate set" back to the GT setting.

Mar 12, 2008 | Sharp EL-2196BL Calculator

I copied this from another post & it worked for me:

To enter the date

1. Be sure to switch to "rate set" from GT

2. Enter the month

3. Press the decimal point

4. Enter the day

5. Press the decimal point

6. Enter the year

Example 3.09.2007

7. Press the button that look like a clock/calendar

To enter the time

1. Be sure to switch to "rate set" from GT

2. Enter the hour (please use military time)

3. Press the decimal

4. Enter the minutes

Example: 13.24 or 9.24

5. Press the button that look like a clock/calendar

Then change the "rate set" back to the GT setting.

To enter the date

1. Be sure to switch to "rate set" from GT

2. Enter the month

3. Press the decimal point

4. Enter the day

5. Press the decimal point

6. Enter the year

Example 3.09.2007

7. Press the button that look like a clock/calendar

To enter the time

1. Be sure to switch to "rate set" from GT

2. Enter the hour (please use military time)

3. Press the decimal

4. Enter the minutes

Example: 13.24 or 9.24

5. Press the button that look like a clock/calendar

Then change the "rate set" back to the GT setting.

Mar 10, 2008 | Sharp EL-2196BL Calculator

To enter the date
1. Be sure to switch to "rate set" from GT
2. Enter the month
3. Press the decimal point
4. Enter the day
5. Press the decimal point
6. Enter the year
Example 3.09.2007
7. Press the button that look like a clock/calendar
To enter the time
1. Be sure to switch to "rate set" from GT
2. Enter the hour (please use military time)
3. Press the decimal
4. Enter the minutes
Example: 13.24 or 9.24
5. Press the button that look like a clock/calendar
Then change the "rate set" back to the GT setting.

Jun 14, 2007 | Sharp EL-2196BL Calculator

967 people viewed this question

Usually answered in minutes!

I WANT CENTS WHAT I GET WHEN I PUT IN A FIGURE LIKE 1500

IT PRINTS 1500.00

×