Question about Chamberlain Powerdrive PD422D 1/2 HP Security Plus Screw Drive Garage Door Opener

3 Answers

Chamberlain Power Drive 1/2 HP - motor runs but does not move chain

When I try to open the garage door the motor runs and runs until I push the button again to stop it but the chain never moves and therefore the door does not open.

Nothing is straining, the chain is not too tight, the motor does not sound like it is working hard, it just does not move the chain.

Posted by on

  • 1 more comment 
  • Anonymous Nov 29, 2008

    Not this one but a Stanley chain drive unit.

  • savnagaj Apr 03, 2009

    Hi Edward i have the same problem...Where u able to find part. Could u give me more details...

  • Anonymous Apr 30, 2009

    I have same problem but i am not sure how to replace it. Do i have to remove the whole unit down to replace the part or i could do it while the unit is tied up.



    Let me know if you guys know to repair/replace the part.

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same problem with the worm gear shaved. I bought the replacement part and replaced the worm gear. The door did not travel to the full distance between the limit switch. It hit the upoer limit, stopped. When I pressed the remote again, it only reverse for a short distance and never hit the other end of the limit switch. Any hints what the problems are?

Posted on Jun 12, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

You probrbly need to replace the gear and sprocket kit inside the opener. Also make sure the trolly is not disengaged. Tug the rope!

Posted on May 19, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same problem. I just removed the cover and discovered a nylon gear had been worn out. I found lots of shavings inside the cover. The nylon gear is beneath the exterior chain gear. I am looking for information on how to replace it, if I can find the part. If you decide to look at yours, unplug the power and remove the sheet metal screws securing the bottom portion of the cener cover to the front and back covers. Then just remove the upper screws from the center cover. Good luck.

Posted on Oct 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Craftsman 1/2 hp, mod # 139.53603. When I press the remote or the panel button there is a humming sound from the motor. I opened the panel on the back and did not see anything out of line, etc. ...


Is the trolley jammed against the bolt just in front of the motor? If so, loosen the chain until the tension is off the trolley and then run the motor until the door is closed. Now locate the up limit on the side of the motor unit and turn this control 2 full turns in the opposite direction of the arrow printed on the cover. Tighten the chain.

Jan 25, 2011 | Sears Craftsman LiftMaster Chamberlain...

2 Answers

(Chamberlain 1/2 hp Whisper Drive garage door opener) the garage mounted opener will open the door, but none of the remotes now work. batteries have been changed already. Is there a way to reprogram the...


If the wall button will operate the door up but none of the devices do then look at the wall button. Find the lock button and push it for 2 seconds and then try the remotes again. This is your vacation lock. You can get a manual at chamberlain.com. Now if the door does not open or close with the remotes you can reprogram them. Press the colored learn button on the motor head and then press the button on the remote. Repeat for each remote. If they fail to program you will need a new logic board. Thanks BB

Aug 18, 2010 | Chamberlain 1/2-HP Whisper Drive Belt...

1 Answer

Door will not move up or down,the drive motor just hums.


On the inside of the motor box, check to make sure the chain has not come off the gear.

Apr 05, 2010 | Chamberlain Powerdrive PD422D 1/2 HP...

1 Answer

When I push the button to open my garage door, the


Remove the cover and take a look at the drive gear. It is white nylon and is just in front of the motor. It is probably stripped. It is a good time to release the door from the opener and try raising it by hand. Your door springs may be weak or possibly broken.

Oct 15, 2009 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Garage door opener closes when closed


Try this: Loosen the chain enough that you can remove it from the sprocket above the motor. Now run the opener until the sprocket turns in the clockwise direction and stops. Reconnect the chain. This will get everything in sync and you will have to tweak the 'up and down limits' a bit to get it just right.

Oct 11, 2009 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Garage Door opened but will not close. I opened


I think the trolley has jammed against the bolt just in front of the motor unit. Remove the bolt and then run the door until it is closed. With the door closed locate the 'up limit' control on the side of the motor unit. Turn this 2 turns in the opposite direction of the arrow printed on the cover. Replace the bolt.

Sep 01, 2009 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Motor runs but gear doesn't turn on my Craftsman 1/2 HP


What did you pay for near gears. curious. often get stripped gears in cold weather as door is frozen down to ground. if possible, kick door bottom edge with heel to break bound if you suspect it is frozen to ground.

Jan 10, 2009 | Sears Craftsman LiftMaster Chamberlain...

5 Answers

Chamberlan 1/2 hp security + not working


sounds like it is out of synch.do you have a manual on this model

May 19, 2008 | Chamberlain Powerdrive PD422D 1/2 HP...

Not finding what you are looking for?
Chamberlain Powerdrive PD422D 1/2 HP Security Plus Screw Drive Garage Door Opener Logo

1,030 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chamberlain Car Audio & Video Experts

Iron
Iron

Level 3 Expert

3018 Answers

yadayada
yadayada

Level 3 Expert

71525 Answers

Are you a Chamberlain Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...