Question about Linksys PAP2T

1 Answer

Pap2 phone adapter

Hi
I find difficult to configure pap2 phone adapter. i am having dail tone but not able to make calls or receive calls.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 535 Answers

Did u have balace in your pep2 line if u not have balance then its will be happen or ur account has been deactived

Posted on Oct 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My linksys pap2 cannot ring the wireless set or a fax machine.


Try changing the power supply.
It could be unable to supply the neccery power...

Jan 15, 2013 | Linksys PAP2T

1 Answer

FWD/DND will not cancel on KX-TDA200


Hello,still having the same problem?I can remotely configure and cancel call forward and configure your system as you want it.Contact me for help.
Mail me: omonat@yahoo.com
Make the subject be PANASONIC PBX

Aug 21, 2012 | Panasonic (KX-TDA200)

1 Answer

Hello, I have a PAP2 working fine until a day the power remain redlight. No more access via FTP none by plugging directly a phone. My PAP2 is dead ? I read a lot of forum without solution. Thanks EXPERT


unplug the unit for atleast 5 mins.then plug it again.
if its still doesn't work try to do this steps to reset in again in factory default.

http://www.exoticpages.info/linksys_pap2t_factory_default_reset_procedure.html

Nov 17, 2010 | Linksys PAP2T

1 Answer

I can not reset admin password for pap2t device


Hi,

You can reset your device with below steps.

Resetting your PAP2 to its factory default settings (often referred to as a 'hard reset') is done via the built-in IVR (Interactive Voice Response) menu. To access the IVR, simply pick up a telephone that is connected to the PAP2 and dial:
* * * *
(yep, 4 stars) This will activate the IVR 'Configuration Menu' (you'll hear a voice tell you this) after which point, simply press the following sequence of keys to 'factory reset' your PAP2:

7 3 7 3 8 #
Funnily enough, the above key sequence spells 'R E S E T', followed by a #. You'll be asked to confirm your selection - simply press 1 to continue. That's it.

Hope it can resolved your issue
Happy to help
Thanks for using Fixya

Apr 04, 2010 | Linksys PAP2T

1 Answer

Hi i have linksys pap2 voip router and am unable to programme it .......can you help


goto ip address 192.168.5.1

or config manual with phone with #* to enter config bia analog

Feb 18, 2010 | Linksys PAP2T

1 Answer

Delay ring tone


after dial phone no. just dial # for quick ring tone and for good sound quality just choose preffered code g723 and save it. Hope you will get solution

Mar 10, 2008 | Linksys PAP2 Network Management Device

1 Answer

Landline phone


I gather you are using an IP phone. I would have to say that the only way to trouble shoot is to use a protocol analyzer. If you connect it within the IP path you will be able to see both ends of the call and determine if the call was received or not and if the other end is responding to your call. Your IP PBX might be the problem I would run a diagnostic on it and if it fails, I would suggest calling the manufacture to see if there are any tests you can run.

Aug 22, 2007 | Actiontec (DHUSB00020C01)

1 Answer

Reprogramming


Open Internet explorer and type the ip address of the router in the address bar and hit enter. (it should be 192.168.1.1) The setup page for the router should open. Click "Advanced" then click "ISDN Configuration" then click "ISDN Parameters" You can enter the new SPID's the phone company gives you there. Good Luck, El Duderino

Nov 15, 2006 | Ramp Networks WebRamp 410i (516S)...

1 Answer

My voice is not being heard


hi alwayes start chcking a problem from the end and back 1) check the MIC on your handset - connect it to something else and see if it works good... 2) check your output if there is any noise (voltage, other system....) if all is good then the problem is probeply in your COMP: check all audio configurations if that didnt help then its a hardware problem.... good luck

Apr 24, 2006 | Actiontec (DHUSB00020C01)

Not finding what you are looking for?
Linksys PAP2T Logo

Related Topics:

419 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Other Network Devices Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Coss

Level 3 Expert

1039 Answers

Tony

Level 3 Expert

2598 Answers

Are you a Linksys Other Network Device Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...